Hello,
I recently got a BL653 Click Board and am trying to program it. As I do not have a supported MCU for the NECTO Studio IDE (the ClickBoard's manufacturer IDE), I...
I was looking down at the pinout schematic of the nrf52840 aQFN73, in the schematic provided in the data sheet from v1.1 to v1.11 VSS_PA pin is below ANT pin, but once in...
Hi,
I'm looking to use the nrf connect sdk for development that is compatible with the latest zephyr lts. I believe it will be ncs 2.9.2 compatible with zephyr 3.7.99 (3...
I'm still new to this but particularly in regards to battery. I have a custom board with a nrf5340 and have been working on reading the voltage. I used the battery sample...
This is NOT a runtime error it's a compile time error (application). Failing at stage [154/159] Linking C executable zephyr\zephyr_pre0.elf
Having started by following...
Hello,
I am designing a custom PCBA based on the nRF7002DK PCBA and I really need the Fabrication Notes / Drawing that officially went to the fabricator to direct the build...
Hi,
I purchased nRF52 DK 2 PCs. PCB labeled
PCA10040
3.0.4
2024.34
boath board are new and box packed. from first time itself. I am not able to flash the board...
I can compile and run the beacon example in long range mode but advertising packets are not being received by any app on my mobile phone. Is there an app that's written for...
I was previously working on nRF51822 ble beacon, in which codes flash of hex 20006.
But i wanted to flash a code nRF5_SDK_11.0.0_89a8197\examples\ble_peripheral\experimental_ble_app_blinky...
Hello,
I want to put my nRF to sleep mode if I dont receive anything on UART/no activity on NUS for more than 10 mins.
Is there any example to achieve that?
Thanks...
Hello All,
We are working on a medical device that requires BLE connectivity. We could either use the nRF52 series SOC to run the application and the BLE communications...
I am using TWI 0 to communicate with an external EEPROM. 99% of the time this is going succesfully. For reasons best known to itself, my eeprom will sometimes fail to acknowledge...
Hi everyone,
I have an nRF52840 DK. So far, I have been programming the nRF DK using the UBS connector J2 and everything worked great.
Since yesterday, by following the...
I want to update status in manufacturer specific data of advertisement packet. is there necessary to stop advertising first then reinitialize advertisement data and again...
Hello peeps,
nRF52480 I2C Interface with Invensense ICM 20948. I am using SDK 15.2. I see there is some Support for MPU 6050 Invensense but not for ICM 20948. A lot of Registers...
Hello,
I am currently working on the nRF SDK for Mesh v3.1 and I am using a static provisioner as in the light switch example. I have merged the client and server functionality...
Hello! I have a custom board with a NRF52832 chip that is working fine with the last program I flashed into. But since yesterday I can’t access it to load a new code (flash...
What all do I need to modify in the Blinky peripheral (from SDK 16) with in order for the 840 DK to advertise and connect with CODED PHY in long range mode?
My code compiles...
Hi everyone,
I am looking at using MQTT v3.1.1 with TLS 1.2, to send data to Azure IoT Hub.
I tested the MQTT Simple sample and it worked perfeclty. So I am modifying...
nrf52832 , I have flashed ble_peripheral/ble_app_uart with simple modifications
ble doesn’t advertise while Jlink/seggar debugger is connected to our custom board.
...
