Hi all,
I'm deploying an nRF9160-based device in India and hitting the familiar "which SIM actually works here" wall. Looking for current (2026) experiences, since older...
Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
As the title，I recently want to use nRF51822 to communicate with SmartCard in ISO7816 interface. but I don't know how to do this.Can anyone share the example code online ...
Hello,
I am using the nrf sniffer from adafruit to pick up ble packets from my NRF52. Everything has been working fine for the past 3-4 months. Yesterday I wanted to test...
I'm trying to create a HID over GATT device that is not a keyboard, nor a mouse. About a week ago, I came close by being able to read some data in an OSX app from the device...
Have project setup to read values from ADC and then run fft_process. Then print them out over uart using NRF_LOG_* statements. However after we call the arm fft functions...
Hello, I am using nrf51822 and SDK11, dual bank dfu ble, S130, 2.0.0.
I made dfu zip file and I modify firmware_crc16 value to the wrong one.
And I zip it again.
But...
hai
i am working with nrf51822 and mbed .
in my application i have requested one page in flash for data store using pstorage.
pstorage_module_param_t param;
param...
Hi,
I'm trying to use NFC type 4 tag on nRF52 side (PCA10040) and poll and read it on Embedded Linux using neard [1]. I'm not an expert in NFC area, so I could be wrong in...
I am migrating a project from SDK 12.1.0 to 12.2.0. According to this question the RAM base needs to be defined in ble_stack_init(). The examples that come with SDK 12.2.0...
I followed the Nordic tutorial on wrapping an SDK sample project in a Makefile managed Eclipse project. I used the ble_app_beacon as the project.
Eclipse will build the project...
I have implemented pwm as suggested in the info centre of nordiac semiconducter. But it showing the following error as shown below image.
Please Help if any one is aware...
Hi,
I think that I found bug in nRF Toolbox release 1.3.0.
1)Application flashing stucks on 95%
2)If you click on Abort, application will stuck in aborting phase. ...
Hi,
Currently I'm working on updating some code based op pstorage on the nRF51822 with SDK 10 an SD S110 (v8).
Right know we're not using "blocks". We're using pstorage_update...
Hi All,
Is there any way to extend RTC2 wakeup interval time more than 2s ?
we know that the maximum interval time of RTC2 on LE1 is 2s, i want to keep LE1 power donw to...
When I just test and build with NRF51-DK there are with BSP Package. such as (pca10028).
But When I make a new PCB Board, Do I have to make my own BSP Package (.h header...
