Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hello, in the NRF Toolbox UART application for iPhone if you navigate the the UART button screen and connect to the nrf52 eveything is fine. You can exit the app (whitch goes...
After some days trying a very simple tx/rx, reading each page of the manual, looking at at this developer zone, etc. I´m still in trouble, with many distinct partial results...
Hi,
I have a problem with my SPIM read buffer.
As you can see below, my SPI device received bytes correctly and answer correctly
My code is based on SPI example...
In the simple_uart.c there is a code:
void simple_uart_put(uint8_t cr)
{
NRF_UART0->TXD = (uint8_t)cr;
while (NRF_UART0->EVENTS_TXDRDY != 1)
{
// Wait for the...
Hello. I wanted to use a receiver on a quadcopter and some becons nearby(+-5 meters). Is it possible to determine the distance IN REAL TIME to the drone?
I'm a newbie to nrf52832 and would like to ask a dumb question here: can I use radio notification to implement a dynamic advertising message? I've looked into this question...
Hi,
As I know that one reading operation requires 2 connection events:
First - ATT Read Request
Second - ATT Read Response
GATT Read Message Sequence
My question...
Hello.
I'm working with the nrf52 with s132 loaded.
There is a way to have a 6Mbps on the SPI ? I try the value 0x60000000 but this do not work.
Thanks.
Eric Provost.
Hi,
there are similar questions to this but I cannot solve my problem.
I am trying to upload a new code using DFU by means of a smartphone (using nRF Connect) or PC (using...
Hi everybody
Is it possible to use secure dfu (SD130v2, SDKv12.2) with 16k RAM dervices (concrete nRF51822 256k flash, 16k ram)? When I try to shrink ram in dfu project...
Hi,
i have an openwrt image running on my rpi. I made sure to build the openwrt image with 6lowpan modules and other bluez library.
i am trying to connect to the nrf52 running...
I am using Martin's code to test my I2C connection.
I use PC10040 evaluation board, SCL and SDA are 3 and 4.
My sensor is a Max 30102 pulse and HR sensor.
I used Martin...
Fight continous! I have NRF51822 chips and today i got NRF51 DK motherboard. I wanted to flash it according to tutorial found here: devzone.nordicsemi.com/.../ .
After some...
