i've noticed that the pc-nrfconnect-ppk is written in typescript (with a lot of .tsx files for visual elements)....
my understanding is that at the lowest-level the power...
I used the "echo_bot sample and tried to alter it to use UART2 instead of UART0. Aftet changing the code and putting in the needed overlay, the main() program begins to run...
I am using the `mcumgr` subsys to enable the DFU (Device Firmware Update) capabilities in a custom device that also features a custom (non mcuboot) bootloader. In order to...
Hi !
I have a peripheral that can connect to other nRF52's or a smart phone such as iPhone or android. Is there an easy way to detect a smart phone?
The best I can think...
Hello nordic team!
Issue:
I am reaching out because one of my nRF9151DK does not seem to have associated character device files created when I plug it into my laptop,...
I have an application that I want to build and run on 5 or 6 target devices including a nRF52840DK, nRF52840 Dongle, and custom boards. There are areas of the code that only...
Is it possible to see LOG_INF() or LOG_ERR() messages from custom board software when the custom board is connected to a nRF52840DK through connector P20? The custom board...
I can not understand how works READY register in SPI master:
after first byte transmission READY sets high, i set READY low and send second byte, but READY never sets high...
I can upgrade the firmware by MCP on air ,But there are one conditions:
reset the device while holding down the Enter Bootloader Mode button or a invalid application is present...
Hi,
I am running (and reconfiguring) ble_app_lbs (LED + Button BLE app) example as a kind of start off project for me. I am actually trying to figure out where I can control...
Hi,
When i increase the global buffer , i got this error.
if i reduce buffer size and add few more characteristic , i am getting same error.
How can i use Flash memory...
Hi All,
I started with example ble_app_multilink_central for S120 from sdk 6.1. I then started stripping the application to get a barebones central. I removed app_trace...
What I`m using:
-nRF51422 EK
-Keil v5
-nRFGo Studio 1.17.1
-SDK 6.0 and 6.1
-SoftDevice S110 v 7.1
-Applicatio: ble_app_hrs
I first Programm the SoftDevice
Softdevice...
I've done a lot of reading on the forums about this topic and done a lot of trying myself. I haven't had much luck and it seems like most everyone is in the same boat.
...
Hi,
On my ble application, I want to keep after wake up reset the previous value of a variable, I tried using sd_power_ramon_set(0x000f000f) to keep on all ram partitions...
It seems like a pretty large hardware/software release just came out and I am a little confused. Where can we find documentation about all the new hardware (nrf51822-QFAX...
Hi I try to run master control panel on PCA10024 development boad. On master control panel, I set File->Options->Serial port: "Show all serial ports". Then master control...
Hello,
I'm reading S210_SoftDevice_Specification_v2.0.pdf and there is written: "The ANT channel encryption engine provides the ability for a single channel..." does this...
I didn't find information about size of buffer within softdevice 310 for ANT messages.
I found that S310 requires: 128kB Flash, 9kB RAM, Stack 2kB
But how big size of...
Hi, are my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS or AIN_2_3_PS will not...
Hello,
I'm currently seeking for parameters that could improve our ANT communication stability. I read, that there are possibly override parameters in the FIRC that have...
Hi all,
I try to reduce the power consumption of my GZLL host (RFDduino/nRF51822).
I use the Arduino IDE to program my RFDuino.
My Idea was to synchronize the host and...
