Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I am using Rowley CrossStudio 4.4 to debug my project. I can program and step through the code just fine, but I can't seem to get any debug out put on the Debug Terminal....
(1) Production Programming using CLI:
We are entering pre-production for a design containing an nRF52810 (on Rigado BMD-330 module), and we need to know what the CLI command...
Hi,
I was referring the timer example code for PCA10040. I wanted to include the timer code in my ble peripheral code which uses custom GATT service. Can you help me with...
I see that the nRF9160 DK has both cellular and BLE capabilities because it has both a nRF9160 SiP and nRF52840 SoC. Wouldn't it be optimal to combine both cellular and BLE...
Hi There,
The attached image shows the part of the schematic responsible for the enabling of the QM14501. I was wondering if there was a particular reason that the mosfet...
Windows 8.1, 64bit PC
I have a nrf52840 app that works from "SEGGER Release 4.30 Build 2019101800.40379 Windows x64" on the DK 16.0.0, and from " nRF Connect for Desktop...
Hi there,
I want to implement the BLE dfu in nrf zigbee and thread sdk but there are no examples provided in the sdk and if i try to use the files from nrf 52 SDK for...
Similar to this ticket , we are no longer able to connect to Verizon using a Hologram SIM after upgrading modem firmware from 1.0.1 to 1.1.0.
I'm attaching a matching console...
Inside gps_controller.c
We issue the following instruction to begin searching for a satellite fix.
k_delayed_work_submit(&gps_work.work,K_SECONDS(CONFIG_GPS_CONTROL_FIX_CHECK_INTERVAL...
Hi,
We are atempting to get DFU over UART working in our project, but there does not appear to be a bootloader project in the 16.0 SDK for this configuration. What would...
Hello, I want to put extra authentication when device is preparing for boot loader. I found callback "ble_dfu_evt_handler". I think inside case BLE_DFU_EVT_BOOTLOADER_ENTER_PREPARE...
Hi,
I am using nRF51822, S130, SDK12.
Now trying to add a level of security with a static passkey, I have done the following adaptation to my code -
Added to void gap_params_init...
The latest nrfConnect 3.3.0 doesn't work anymore for me, and is apparently full o' bugs (according to this: h ttps://devzone.nordicsemi.com/f/nordic-q-a/49331/nrfconnect-3...
