Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
In the nordic documentation it mentioned that in the init packet we can write list of supported softdevices so that if one of that matches it will start the dfu. But in Signed...
Actually, I'm not good at using English. So I'll try to struggle to type this question...
Sorry, Last week. My boss gave me a Nordic Mouse to develop some embedded one...
Hello,
I am using nRF51822 and meet a question that in the process of bluetooth communication, I will get an instruction for external circuit to stop bluetooth function...
While both P0.00 and P0.01 has Analog Input function, initializing an AnalogIn (in mbed) with P0.00 will cause the firmware to fail to start at all; but initializing using...
Please tell me the Manufacture Part no: which is used for the 16MHz crystal in the PCA10040 DK. I found it different from the one used in PCA10028 version of the DK with just...
Please tell me the location to download the hardware files for pca10040 version of the nRF51 DK board. I could find only pca10028's hardware files in the nordic's webpage...
Hi,
I have some similar problem when trying to add the custom 128bit characteristic UUID.
The service UUID is advertised correctly but the characteristic UUID not.
...
Im using nrf51822 (16KB RAM), I'm trying to retain some data (RAM) after watchdog reset. when I load only the softdevice and my app, the RAM retention workings, but when I...
HI , ALL
i coded the uart_init in my project.
and i want to regarget the printf in my project.
so i find the retarget function is in the 'retarget.c' ,
i tried...
Hi,
We are using Softdevice S310 Version:3.0.0 and SDK:9.0.0.
My Device working on battery power. We are facing Flash write problem when my battery voltage goes to below...
Please tell me the safe 'Max Voltage Rating' for the capacitor at the DCC pin of the nrf51822 in DCDC mode. I am talking about the C12 cap in the circuit shown in Page 113...
Hi all,
I have an interesting problem where I want to read my bootloaders version (based on the DFU), which I have located at 0x3C100, from my application.
I confirmed...
HI , ALL
in the PS document, i know that there a register for the interruption --- INTENSET.
i wanna know if there is an api to set the interrupt.（or the only is to...
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
