Hello team, I am currently working on the distance measurement functionality using the development kit (nRF5340 and SDK: v2.9.0). At present, the distance measurement runs...
Hi,
Right now I'm looking down at the nrf52840 datasheet, because I would like to do a project with such MCU, but I got to the part of the integrated DCDC converters and...
Im working with:
-Windows Nordic Connect for Desktop App v5.20.
-Direct Test Mode v2.5.0
-nRF54L15 flashed with ncs v2.9.0 direct_test_mode example
There is currently...
Dear team, in my design I'm using MCUBOOT to perform FOTA DFU over BLE and I need some confirmation about the building process to be sure to do all the step in a properly...
Hi!
I'm migrating my development environment to arm-based Mac. I succeed to install nRF Connect for Desktop app for aarch64 architecture, but struggling to get Bluetooth...
Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello :
I come from STM32 programming and I am new to Nordic device programming.
for nRF52840 DK, I am looking at the ble-blinking example and try to understand Softdevice...
i am working nrf51822 and SDK V10 SoftDevice S110. I was using some old version of nrfutil ( dont know version ) to generate zip file, that was working fine. when i start...
Is there a way using the API to utilize all 31 bytes of advertisement data for a user application? I'm porting an application, which sends data in advertisement packets, to...
Hi,
I need nrf_malloc and nrf_free for my application but I cant find which files should I include to be able to use thees functions.
Thank you very much
Hi,
I would like to evaluate the long range demo with the 15.2 SDK (original 15.0 is used). Opening the project and trying to compile it gives some errors like "no such...
Hi support team,
I have found that RESN and RESP are typically 160 ohms, customer would like to know their stability and temperature coefficient.
Regards
Salas
HI,
Version: SDK15.3,ble_app_template,custom board with nrf52832
I'm trying to change my device name by writing data from bluetooth
when getting 0xdd 0x06 ........,it...
Hi What is the minimum clock frequency that the TWIS module will work with? Obviously the I2C spec minimum is about 100kHz however the device I am communicating with is using...
Hi,
Is it possible to use the modem firmware mfw_nrf9160_1.1.1 (delivered with nRF Connect SDK 1.2) with nRF Connect SDK 1.1?
We will move to nRF Connect SDK 1.2, but...
Hello, we are integrating a BLE board (nrf52832) into our system, and the ble_app_uart example project is perfect for us, so we are starting with that.
What we are seeing...
After reading some questions about the Thingy:91 here in the forum, I start asking myself, if the Thingy:91 without a nRF9160 DK is usable at all.
Any experience with that...
Hi, I'm working on a design with nRF52832 + chip antenna. I'd like to add a PI network to be able to tune the antenna before production.
I'm working with this antenna:...
OK, I have an app that succeeds in starting advertising and then arrives in the main event loop, following which I go to the NRF_BREAKPOINT_COND trap.
Since I do not have...
hi,
I am using Running Speed and Cadence Service structure, when i raise a write command (bt_gatt_write) from the client I was expecting a BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST...
OK, so I have figured out that I can put some of my advertising content into the scan response if there is no room in the advertising packet, but what do I do if there is...
