Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
Hello
We are using nRF5340 as our EVK with a 12 antenna array plate(4x4 with center 4 ones not being there). Our beacon uses nRF52833.
We used Nordic's sample codes- ...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
This is related to the new nordic dev zone, not nrf connect, but there is no dropdown option for it.
After signing into the new nordic dev zone for the first time since...
Hi there,
I'm using ASUS RT-AC1900P router with IPv6 DHCPv6 on. RPi gest its own IP with prefix specified in router but interface wpan0 (wpantund) not. I have configured...
just like the title.
I'm using sd_radio_session_open APIs very similar with
https://github.com/nordic-auko/nRF5-ble-timesync-demo
and add data uploading by gatt.
using...
Hi, all!
Sorry, I'm not good at English myself.
My device is nrf52832. Base code is ble_app_uart (sdk 12.0.0, pca10040, s132).
ADD. fs_sys_event_handler
ADD...
My develop board is nrf51822 and the SDK version is 9.0 softdevice s130. Because the NRF51 board is build by the customer. So the UART connect pin is changed from {13,14,12...
Hi, I am in the schematics phase of a new device which may talk via BT to lets say a mobile phone. The communication between the new devices CPU and the nRF52810 shall be...
I'm trying to connect my nRF51 dongle to the DK using the Master Control Panel3.10.0, but I keep getting "no response from master emulator" and failed discovery. I read the...
How do we go about adding servers to the light control example i.e. I would like to control 50 servers via one client. What needs to change in the code besides SERVER_COUNT...
I am modifying the BLE UART example, client and server, in order to have a higher throughput. I have selected that the connection interval is 7.5ms with a total number of...
Now I'm done from send data to the light_client light_service, but I don't know how to send data to another light_server let light_server, I look at the related documents...
I am having issues with the pin_change_int example. I have not changed anything to the code, but it will not load onto my board. In fact, pressing load in this project doesn...
I am trying to implementing eddystone for my nRF52832 and I found two library.
One is with the " /examples/ble_peripheral/experimental_ble_app_eddystone " inside nRF5-sdk...
Hi, I want to NFC connection. so I'm trying to NFC examples.
But, while i was testing NFC_writable_ndef_msg example I have some trouble.
Following the example, I succeeded...
Hello everyone I have a problem where I want to know when a node (server) connects to the gateway (client), how can you control which node, for example, turns light on and...
Hello, I am trying to run the SAADC example code alongside the ble app hrs example. I am able to run both examples individually just fine but when I copy them over to one...
