Hello Everyone,
I try to develop Nuvoton + NRF24L01 SPI communicate each other. And I don't understand why MISO bus has 0x0E after I send Write_Command 0x20?
void NRF24_AdressTX...
Hi all,
I'm working with my custom nRF9151 board and i'm testing https request with option that use native TLS for my download client.
I got connect err = 22, so i come...
Hello,
i am currently trying to build a minimal firmware for the nRF5340 on the Thingy:91x. Unfortunately my build failles to link zephyr/zephyr_pre0.elf:
My suspicion...
On the nRF54L15, how can I update the maximum TX time to 17040 µs when using Coded PHY?
I'm currently testing with the Throughput sample in nRF Connect SDK v2.9.1. During...
Hi,
I'm currently working with the Thingy:91X and would like to measure the total current consumption of the entire board using the PPK2. I understand that the PCA64165...
I'm not sure if this is the right place for this question.
I'm using the Settings subsystem for the BLE name.
When BLE is initialized inside matter, settings_load is only...
Hi,
I'm using the nRF51822 for a beacon and following the ble_app_beacon example (SDK 8.0.0) with some modification in order to measure the battery level through the ADC...
Dear Nordic:
I try to use pca10040 DK and SDK is nRF52_SDK_0.9.2_dbc28c9.
Test nRF52_SDK_0.9.2_dbc28c9\examples\peripheral\UART the function work well on my DK.
I...
Hi,
I have some questions regarding connecting multiple (as many as possible) BLE peripheral devices to a single central (simultaneously).
1:
Does anyone know of any...
Hi
I now is developing Android apps on the basis of NRF UART v2.0.
My s110 NRF51 device will switch two modes for differnet 128-bit UUID. These two modes have independent...
The Bluetooth 4.2 specifications allow for an L2CAP MTU size of up to 255 bytes. It looks like the CC2640 already supports the maximum MTU size of 255 bytes with a 248-byte...
Sometimes windows lose the connection to the nRF51 Dongle. The only way I have been able to reconnect to the dongle is by unplugging and replugging it to the USB port. I have...
Hello,
I am currently working on a project where I need to be able to control an RGB by writing the PWM duty cycle to a custom BLE Service and Characteristic. I am using...
When I init, uninit, and re-init a PWM with pin_polarity set to APP_PWM_POLARITY_ACTIVE_HIGH, the actual polarity of the signal is active low. This also happens when I init...
Hello,
I am getting the error code 0x3004, because I am transmitting data too quickly and filling up the transmission buffers.
From other posts, I know the solution...
I'm trying to perform OTA programming with DFU.
when I load only softdevice and bootloader I got address xx:xx:xx:xx:xx:2E
then I load the app with DFU, now the address...
nRF5_SDK_11.0.0-2.alpha.
I create peer by peer_manager.
When initializing the application, i delete them pm_peer_delete_all().
There's an application is stuck.
It works...
Hi
I have a serious problem with stability in "UART" communication over BLE.
I use the command:
err_code = ble_nus_send_string(&m_nus, &bleBuffer, 20);
where I send 20...
I have the following:
Dev board PCA10040
SDK nRF52_SDK_0.9.2_dbc28c9
Mac OSx
I was able to compile the blinky example and have the .hex in the _build folder...
I have several services on a nRF51 peripheral, and would like to have different initialization based on which service is being connected to. The related code is below:
...
