Hello,
I have a legacy project that is using nrf5 sdk v17.0.2. I need to add the BLE DFU functionality to this project based on the nRF52840. Are there any examples on...
We are trying to evaluate nrf9151 for working with Soft-SIM. Are there any instructions for configuring the Soft-SIM through AT command mode, or do I need to use another mode...
I was doing some developement for a custom board on NCS v2.9.1 when i noticed some of the changes i was making in my prj.conf weren't being set in the application. My impression...
In my circuit I have a MOSFET which disconnects the battery. There is a GPIO pin which turns this device on and I'm using regulator-fixed to drive it during start-up. A short...
We are currently using ncs 2.9.0 on an nRF5340. We use the BT_HCI_OP_VS_READ_VERSION_INFO to determine at runtime what version of the BLE stack is present. This information...
Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
Hello,
we have a working system on the nrf9161 that works without zephyr. We have our own secure firmware that successfully uses the cc310 after we start the actual application...
Hi,
I have been having a lot of problems communicating with an Atmel SAM D09 as a slave, and an nrf51422 as a master.
I seem to have two problems, hopefully solving...
Hi all,
I design the kb based on the SDK6.1 and SD7.1 with 51822, and doing the PTS certification now, but meet some problem on TC_CON_BV_01_C, ATT Write error, such as...
the error messages show following:
compiling system_nrf52.c...
RTE\Device\nRF52832_xxAA\system_nrf52.c(92): error: #136: struct "" has no field "A0"
RF_TEMP->A0 = NRF_FICR...
Hi guys, I use old project try to build again in Keil when I installed nRF51_SDK_8.0.0. But I get the:
.\Objects\ble_knob_detection.axf:
Error: L6200E: Symbol
GPIOTE_IRQHandler...
Hi guys,
Has anyone encountered following warning message when using nRF51 SDK v8.1.0 or 9.0.0 and compiling project by GCC arm-none-eabi (I'm on V4.9 2015q2 which is the...
Hello,
I have a peripheral that manages several bonds to known centrals. Assume I want to pair with some fresh central, yet I need to do that within physical reach of another...
Hi, This is Venkatesh. This is my first question posting here. It is great pleasure to use this product. I have installed SDK of NRF52832. but I am not getting "boards" folder...
Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Hello, I am using RedBear Lab Ble shield v2.0 having nRf8001, with Arduino Uno as peripheral and sending data to my mobile.
But now my application needs to receive data from...
Hello,
I would like to ask you guys whether it is possible that one Bluetooth master device (smartphone) can control and collect data from two Bluetooth slave device (some...
Hello all
I'm struggling with link errors, "undefined referencce atan2" as well as all math library.
I still dont know why it is occurred these errors.
I configured the...
Hi,
I'm trying to move my code from Red Bear BLE shield with Arduino to nRF51 dongle.
Is there any possible method?
(ex. share the same library or SDK helping)
I just read the S13x migration guide .. have some work to do :(. I'll have to read it a few more times to get my head around the bandwidth configuration but it looks super...
Hello, I started with NRF24L01 + Arduino and that works fine for me. Then I saw the nrf24LE1 and I thought that would be smaller and cheaper. I ordered the NRF24LE1 development...
