Hey Team,
I'm trying to flash the audio application on our custom PCB, this PCB follows the interfaces of the nrf5340 audio dk. Previously on lower SDK versions (2.7-2.9...
Hi Nordic team,
This is a follow-up to my previous question here:
Can nRF52833 perform PAwR while also syncing to another PAwR device?
We are now extending our design...
Hi,
I'm trying to build nmea parser, so I have a functionc hecking all nmea sentences and trying to get double value, but I always go bad double value. For example here...
Hi
I am trying to setup and test the OpenThread CSL feature on nrf52840DK with OpenThread daemon and RCP mode nrf52840DK.
I found there is a way to build the Daemon for...
Hi,
With several nrf52840 based prototypes, I had serious problems. I could see them die after flasing them a few times. And this was not just one dying, it was all of them...
Is a common ground required when measuring current in current meter way?
Can externally supplied voltage exceed 5V? Will this cause inaccurate test results?
I'm working with nRF5340 and nRF Connect SDK 2.9.0, using sysbuild and Partition Manager for my project. I want to enable Zephyr's coredump feature and store dumps in internal...
I get NRF_ERROR_SVC_HANDLER_MISSING error in spi_open function.
uint32_t err = sd_nvic_ClearPendingIRQ(p_spi_instance->irq_type);
APP_ERROR_CHECK(err);
I'm using...
hi,
I need to store persistent data of about 32 bytes in flash, so tried using pstorage APIs (SDK v9.0 on nRF51822 -- 256KB ).
I followed the sample code given here...
Hello,
I am using keil uvision 5.17, sdk 9.0.0 and sd 130.
Once I programmed whole application through mbed,
Then I moved into keil and implemented all function....
We are trying to communicate to NRF51422 through PC using UART communication. But the programs works fine with nRF51822 Dongle and DK. But it does not works with another dongle...
Hi experts,
I need nrf51822 to send thousands of packets (notification) to Master Control Panel (PC), and expect for high data rate. So, I turned the connection interval...
if initial uart_config() before ble_stack_init(), softdevice_handler_init will be failed!
with SDK 6.0
softdevice_handler_init() will returns 0x00001001 ("NRF_ERROR_SDM_INCORRECT_INTERRUPT_CONFIGURATION...
I am trying to generate code using BDS and the Nordic Plugin 1.2 but I keep getting the following error. I have reviewed the XML but I can't seem to find the issue. Any thoughts...
I've been fighting this bug for a few days now and I thought I'd share what I discovered in the process.
I wanted to set up a couple PWM channels to control a few LEDs...
getting problem in implementing uart. code is here
#include <stdio.h>
#include "boards.h"
#include "app_util_platform.h"
#include "app_uart.h"
#include "app_error.h...
I implemented measuring of Lithium battery level with the help of thread How to measure Lithium battery voltage . I am using nRF51422 with SoftDevice 110 and SDK 9.0.0 and...
Greetings,
I'd like to develop a wireless sensor network based on your products, but have a few concerns based on my lack of knowledge of how Bluetooth LE works.
I've...
We are running FreeRTOS on the PCA10028 development board. We have bumped into an issue where the code asserts if we turn on the FreeRTOS configASSERT functionality. It is...
Hello,
I am using nrf starter kit and nRF51822 DK modules atached. I'm using external usb-com uart modules (based on FT232 chips) for communication with PC (Win7) and hyper...
