We are developing HW that includes nRF9151 running DECT NR+ with the Wirepas stack for mesh connectivity between multiple units. The product is expected to move between geographies...
Hello Nordic Support team,
I'm receiving the Transmission failure and Lora Initialisation failed message despite to correct wiring and everything else. I'd attach a link...
Hi，
Platform : nrf52840, NCS 2.7.0
I would like to get the MCUBoot image swapping progress without modify the NCS, and display a progress bar on the LCD to indicate the...
I enable cs procedure and set the procdure count equals to 3, let procedure interval to be 10.
I want to change the cs channel map between procedures. so when I send HCI_LE_CS_Set_Channel_Classification...
Hi,
I am working with the nRF54L15 and I want to use it both as a BLE central and as a BLE peripheral. So, I have two separate source files: one for central and one for...
Hi all,
nrf54l15dk,v3.0.1,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
Finally...
We use several Nordic chips in our BLE sensors. We bond to the devices from Android, connect to update configurations, then disconnect such that the device then advertises...
Hi
We are using the SDK files in our hardware projects and in our simulation environments to verify the functionality of our platform. While doing tests with the new SDK...
Hi All：
I'm working on ios ble midi proj. I have modified ble_nus code for my proj, I was modified the correct service uuid ,characteristic uuid , connection_interval ,latency...
Hello
I have recently downloaded SDK v10 for nRF51822 development using Keil uVision 5.14 IDE.
I am wishing to combine SPI slave function with custom BLE services/characteristics...
We are trying to find a way to send the High Frequency Clock directly out to a gpio pin. The reference manuals don't seem to have anything obvious.
Is there a way to do...
Hi,
I am trying to use PStorage to save simply 40 bytes of data onto a flash drive but for some reason the PStorage handler never gets called when I try to store and clear...
Dear all,
I need to measure a pulse width on a GPIO pin which is in between 100mseconds and 7.2 seconds long without the use of "regular" timers due to low power requirements...
I have migrated a new project from SDK 9 to 10, and now I seem to be having issues.
I'm using the uart_fifo to read data from a GPS, so the data shows up every 1 Second...
I would like to use pstorage to store some data.
From the developer zone I know, that the softdevice has to be used for pstorage.
I'm asking me, what will happen with...
i downloaded source code from github.com/.../nrf51-ble-app-lbs . and i am getting error like C:\Keil_v5\ARM\PACK\NordicSemiconductor\nRF_DeviceFamilyPack\8.2.0\Device\Include...
my issue is that when I use the bootloader to get DFU working it advertise DfuTarg and doenst show my services. I searched for hours, I found many answers and none worked...
Hi,
I am developing an application on nrf51822 chip. I have set
#define SEC_PARAM_MITM 0
#define SEC_PARAM_IO_CAPABILITIES BLE_GAP_IO_CAPS_NONE
Also i am developing...
Hi Nordic support,
I want to use the OOB key pairing and I found the below discussion:
Set OOB key on Master Control Panel?
This means I need to implement the application...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
I am trying develop a project in which when we request a characteristic from phone( read request), we will read data from other module through UART and give reply back. I...
