I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hi all,
i want to add a cts service to my project.
i started with ble_cts example of sdk 11.0, but it's not clear what is the correct procedure to do it.
I add the service...
I tried to add a dfu service to the SDK 11.0.0 ble_rscs_app by following the procedure here . I was able to successfully compile and run the application, and when Master Control...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
Hi all
We use the nRF51822 with the S130 V1.0.0 in the peripheral role and a Galaxy S5 in the central role. As soon as the S5 connects to the nRF, we send a connection...
Hello,
I have been working on a customised Nordic Board ,and I can't be able to do a DFU. The DFU App_dfu_dualbank doesn't display the DFUTarg Bluetooth profile on the board...
Yo man,
I use nRF52 with ADC fun in SDK11 and I want select ADC input to internal VCC.
I modify like below:
static nrf_drv_adc_channel_t m_channel_config = NRF_DRV_ADC_DEFAULT_CHANNEL...
Does the Bluetooth Peer Address of NRF51 Chips change randomly [every 15mins] or does it remain same?
When implementing whitelisting for secured connection, it is required...
Hi, I am unable to build this example in Keil Uvision5. I am getting following error:
"no source": Error: #5: cannot open source input file "......\main.c": No such file...
Hi,
I am trying to setup a testing environment using nrf51-ble-driver_win_0.5.0.
All of my job are:
Download nrf51-ble-driver_win_0.5.0, and program connectivity_115k2_with_s130_1...
Recently updated to SDK11 + s130 v2.0.1 on an nRF51822 xxAC LFCLKSRC=RC
BLE Advertising no longer works. Localized it to our use of TIMER2 for an implementation of systick...
Hi,
Im trying to connect MCP25625 via SPI on nrf52. I checked with the scope that CS, MOSI and SCK are correct, but I get no reply on MISO line whatsoever.
I perform a...
Every time I want to connect to Nordic ble device from my Phone, it ask for pairing confirmation and then it create bond. That's how it should be.
But if the device is...
I'm using nfr52 with softdevice s132.
I want quickly perform flash write during power loss.
When I realize write using fs_store() I obtain time more than 5 msec.
How can...
Just do
NRF_POWER->SYSTEMOFF = 1;
in main()
and found if it's boot by powerup
the current is 10.4uA~10.5uA
and if a re-flash the hex, the current is 1.4~1.5uA
...
