Previously, I designed a PCB for the nRF52832 chip using the RFANT3216120A5T antenna ( link ). However, I was only able to achieve a very limited Bluetooth range of around...
Hi, I'm relatively new to Nordic microcontrollers and have recently completed the beginner's course. Sorry in advance if I made an obvious mistake.
I am currently trying...
We are running a nrf54l15 board that uses an NFC T2T tag to encode a URI to open an application. We have noticed that sometimes, the current stays higher (~200 uA) after the...
I’ve got a bit of a hardware issue with the nRF52811 UART, receiving DMX data from a Chinese DMX controller.
Standard DMX data-rate is 250Kb/S, so the minimum bit time is...
Hi,
I am using the Nordic UART Service (NUS) peripheral and central on two nRF52840 DKs and I am developing with nRF Connect SDK v3.0.0 .
I can't manage to increase the...
I am getting an occasional softdevice assert on a BLE central device (hub). Both the central and peripheral devices are nRF52840 using Coded PHY and NCS v2.7.0. This error...
I am trying to keep nRF5340 in sleep state, and wake it up when there's a user input (e.g., button) and send a packet as fast as possible to iOS18. What would be the latency...
Hi
I have a problem using TWI driver with my softdevice enabled.
The TWI is able to communicate successfully to the slave without the softdevice.
But the same code...
Now that my application finally supports OTA DFU, I hit a new problem. Instead of nRF51822 starting the newly flashed application, some old version seems to start. Or at least...
Just a general plan not a detail one . like this: in the SD132 2.0.0 we will add the funtion of change the MTU up to about 150 bytes，at the approximate time 2016-4
I am testing the freertos port, based on the hrs example in the new SDK 10.0. I have run into an issue while using the uart during long transmission sequences (where the fifo...
The alpha release of the S332 is now available and I am just curious which example included in the 0.9.2 SDK would be the best jumping off point for building a new project...
I just realized that I have the nrf52 board (with nrf25832) which actually explains a lot but the end goal of my project will be using the nrf51822 (because the nrf52 chip...
Hi there,
I am using the nrf51-ble-driver_win_0.5.0 to communicate with peripherals via the PCA10028.
My problem is when I call sd_ble_gattc_write() in my Windows application...
Hello Everyone,
I am trying to add the pwm library in the button example in SDK verrsion 10 but app_pwm.c files showing this error can anyone letme know why this error is...
I use s130 based device as central to connect to my ios device, when connected, the central will issue a bond request, if user accept this request on ios device, the bond...
While using PPI and trying to use the first channel as a clock based PWM running on timer1 I noticed that whenever I use more than 2 PPI channels, the pin that is toggeling...
Hello!
I have multiple peripherals and multiple centrals. I'm trying to make one peripheral to connect only to one central.
I read a way to do this is by using whitelisting...
I’m attempting to use an nRF51 dongle with connectivity_115k2_with_s130_1.0.0.hex burned on to it. I’m using the dongle as a central, attempting to connect to a peripheral...
Hi, i try to add a passkey with "ble_app_uart".
I want to this thing.
If i try to use the master_pannel app to connect, peripheral require passkey.
no bonding.
...
Hi all;
I have a hardware question . How much is the discharge time of 10uF capacitor which put in the VDD pin of 51822 ?
When i use the formula of capacitor discharge...
