Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi~
I used keil software environment for development.
Apply Ble UART example code from nordic keil example.
Example code down load to nRF51 Development Kit and run, program...
Hi, i need to calculate the frequency of two PWM.
When it comes to frequency calculation, the counter function is the best solution, i think.
i'm using SDK 6.0.0 for...
I want to develop an app that wakes app from sleep mode after pressing 2 buttons, then if these buttons are still pressed for 5 secondes i want to do an action ..
Any idea...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
Is there a call to read the stack ID.
For example S120 v2.1 has an ID of 0x006B . nRFgo studio is able to read and report this value.
Is there a way to read for me to...
I'm using SDK 11.0 and example\ble_central\ble_app_hrs_c
I have cut SB1 SB2 to disconnect the 32Khz crystal from the pca10028 and configured the example program to use...
Hi, When I write data synchronously to memory (nRF51822), I do :
APP_ERROR_CHECK(pstorage_block_identifier_get(flash_handler, 2, &block_handler));
APP_ERROR_CHECK(pstorage_clear...
Hi,
Im having a problem with connecting my phone to nrf DK.
im trying with apps from examples and they work well with HTC one, but my Samsung S6 fails to find device ...
I flashed dual bank ble bootloader from newest SDK (6.1.0) and used it to load my application to chip. I also modified my application (according to instruction here: devzone...
Hi, I have two device. S120 Scanner and S110 Peripheral Device.
At Scanner, I use SDK 9.0.0 and S130 1.0.0, At Peripheral Device, I use SDK 9.0.0 and S110 8.0.0 ..
Scanner...
hello,
I have a custom board which works fine with SoftDevice+Application , but if i Combine a boot loader hex that i complied it doesn't work. But the same ( bootloader...
I found and implemented an example that gives me a decent idea of how to go about polling for data with the UART/FIFO. However this doesn't give any indication of how to use...
Hi.
Trying to set up the Ubuntu development environment for you nRF52 development kit.
I followed this tutorial:
devzone.nordicsemi.com/.../
Stuff done so far:...
