Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
This is a product based on nRF52832, which uses BLE Bluetooth to scan iBeacons and communicates with an LTE module via UART for data reporting.
It occasionally enters the...
Hello,
I would like to measure the current consumption of my nRF9161 and compare the result with a standard measurement. While searching in your documentation, I found this...
Hi everyone,
I’m using a custom board (a tracker) that can travel at speeds up to 65 km/h and transmits data regularly every 200 ms. I expect, therefore, that the inactivity...
From the examples of SDK 17.1.0 (I'm Not using Zephyr), I'm trying to connect to a beacon's Generic Access Service, so I can read the characteristic 0x2A00 and then read it...
Hi Nordic team,
I’m working on a custom LoRa interface using the Thingy:91X, and I’d like to know whether the Qwiic connector pins (P0.03 – SDA, and P0.04 – SCL) can be...
Hello,
I’m working with the Matter Light Bulb sample in nRF Connect SDK v3.0.0 , and I’ve run into build issues when enabling certain optional commands in standard clusters...
Hi NRF team,
I am working on a patient monitoring system where we have used a stereo microphone. I am using the LC3 compression method and the Zephyr PDM microphone driver...
Hi,
I have three nrf5340_audio_dk boards that were programmed with premade images for a BIS audio demo: one gateway and two headsets. I'm currently using VSCode with nRF...
I´m trying to change the installation path of the Nordic Power Profiler as I´m running out of space.
I have about 9GB left, but when trying to open a captured file, Power...
I am experiencing an issue with my nRF915DK board. When I connect the board to my PC via USB, the debugger LED blinks continuously.
I have the same issue with a nrf52840DK...
My application is based on the ncs nrf5340_audio application, but my application and hardware target are both out-of-tree and I am using ncs v2.9.0.
I am able to connect...
I've updated the nrfconnect sdk to the version 3.0.1. and the zap tool version is 2025.5.22. The sdk supports matter 1.4, but the new device type of mounted dimmable load...
Hi,
1.Please provide the documentation, examples and tools for testing the RF performance of nRF7000 during the mass production of nRF9151 + nRF7000. 2. If not, please provide...
Hi,
I'm working on a custom board based on nRF52840 and a 2.9" ePaper display (SSD1680) connected via SPI using the mipi-dbi-spi interface. I'm using nRF Connect SDK v3...
Hello,
Not sure where to post this or who to notify, but after the most recent Nordic DevZone site maintenance, I keep getting multiple emails from the DevZone with the...
