I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
Hello, I'm getting started with a nRF52832, I've got the SDK 16.0 installed and what I think are all the latest packs installed. I try to build the examples\ble_peripheral...
Hello everyone.
I'm trying out the "Zigbee Multi Sensor Example". infocenter.nordicsemi.com/.../zigbee_multi_sensor_example.html
I have 2 nRF52840 devices.
I wrote the...
When my program starts, I set up a watchdog timer for 100 milliseconds and I start a repeated app timer that runs every 90 milliseconds to feed the watchdog. I use the app...
I'm trying to send data via UART from a NUCLEO-F401RE to the nRF 52840 DK. But the data I send is not comming through correctly. For example when I send 3 the nRF prints 32...
I have an existing product to which I need to add SPI to get Wifi compatibility. Basically the Nrf52 is acting as central and passes BLE events on to an ESP32 with Arduino...
Hi.
I have nrf52840-dk board. i tried the UART example from the peripherals directory. it works with the default, if i open a console on /dev/ttyACM0 and on /dev/ttyUSB0...
Wanted to ask if there is any example on configuring the GPS into single shot mode.
I know the asset tracker can operate in continuous_mode and continuous_power_saving_mode...
I am attempting to use SDK15 with the nrf52832 to communicate with multiple sensors over I2C. However, in the twi_sensor and twi_master_using_nrf_twi_mngr examples, as well...
I am using the nRF52840 with the SoftDevice disabled to run a proprietary RF protocol. For much of the time, I have the radio in continuous receive mode by making use of the...
I have a nrf52 application that samples four saadc channels at 1kHZ. That is: Map four pins to ADC input and let Easy DMA take care of the sampling so that the data is processed...
Hi,
I have measured QSPI current consumption on our product at no access period, and got 1mA (too high current!).
So I tried to check with nRF52840 DK to confirm our...
I need to have two different peripheral profiles (with different addresses and so) that will be advertising at same time and that can be connected by different centrals at...
Hello,
It might be a stupid question but I wonder if it is possible to use the ZCL generic command from the CLI to send ZDO commands? I tried it with the ieee_addr ZDO command...
We intend to use the ZigBee stack together with another communication stack and BLE. For the other stack we also have just a library (.a file).
Now we get an error message...
development setup: sdk: nrf5_sdk_15.3.0 LE protocol stacks: s112_nrf52_6.1.1_softdevice toolchain: MDK-ARM Professional 5.28.0.0 description： when we use ble HID or HEADSET...
