In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
In the recent past, I used a SoC in which GPIOs could be configured as "open drain", that is in which there is an internal transistor where the SOURCE is grounded, the DRAIN...
Hey,
I'm using nRF as a SPI slave with a Raspberry Pi. I'm seeing that even at ~3MHz SPI frequency, my first byte transferred gets corrupted. I have a test setup where...
I am using nrf52 with s132 and armgcc
As I add functionality to the code I get to a stage where it fails. Linker runs OK but the result fails to execute.
The observable...
I am currently working on a BLE beacon project on nRF51822. Using SDK 12.3.0 and s130. The device has to advertise URL, advertising name and output power level. And these...
I am trying to control a current measurement chip (DDC114) that works with a protocol that is close (enough) to SPI. It has 2 channels, s.t. it can be read out and integrating...
I am attempting to run my first bit of code on my Nordic nRF52-DK and every time I have attempted to upload the code to the board, the board disconnects in the middle of the...
Hi, I'm using nRF52832, SDK13.0.0 as peripheral.
My iPhone app(my company's) makes connection without problem.
But Android app gets connection fail when it tries to connect...
Hi @ all,
We tried to enable debug log for lwIP module by setting NRF_LWIP_DRIVER_CONFIG_LOG_ENABLED in sdk_config.h to 1.
This threw two errors during the build process...
Hi @ all,
by working on a MQTT project using IoT SDK v1.0.0 (SDK v14.1) we discovered problems with TCP packets not being transmitted.
Using lwIP, transmitting TCP packets...
Hi there,
I was able to work with uart ble example described in tutorials/36/.
My question is how to disable encryption on BLE link? Specifically, we need to make disable...
Hi.
I'm testing multiperipheral function,
and have established multiple connections (1 single Peripheral with multiple Centrals).
But it seems that the Peripheral can...
I have no idea what is going on.
I am using IAR 7.8 and as I wrote, it gets reset when it hit the breakpoint.
every variable return to its initial value, and BLE get disconnected...
Hello,
I was wondering whether or not the standard analog pins on the nrf52832 have to be defined as analog inputs with the gpio methods.
I ask this because I am trying...
Hi there, I was able to work with uart ble example described in tutorials/36/.
My question is how to disable encryption on BLE link? Specifically, we need to make disable...
Hello All,
We need the following for reference purpose only
nRF6939-HW
nRFready Smart Remote 3 for nRF52 Series Hardware Files
www.nordicsemi.com/.../nRFready...
