We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi there,
I'm using nRF52840 dev kit board and v15.2 SDK.
I've set up a PWM using the PWM driver and is working well.
I'm frequently stopping and starting the PWM...
Hello everyone,
I have a nrf52832 (SDK v15.2.0) that is connected to a tablet via BLE. However, if I have several SPI transfers one after another, the BLE suddenly disconnects...
I am trying to retain the data on the board when it is transferred from my computer to the board through uart and once it is on the board through bluetooth to phone. Text...
I am now facing the following issues: https://devzone.nordicsemi.com/f/nordic-q-a/55975/about-reset-during-advertising
I call "sd_app_evt_wait" and go to sleep. Even when...
Hello Nordic Team,
I am creating application to connect with specific device using Name filter,
control is going to nrf_ble_scan_connect_with_target , where "sd_ble_gap_connect...
HI,
The code number for this softdevice version is 0x98. You can find the softdevice code number by typing nrfutil pkg generate --help
But the command only list upto...
Good morning; I am from Argentina, working in a Big Data Project using NoSQL and SQL tools. In fact, I deployed a architecture using Elasticsearch mixing ML, prediction, KPI...
Hello,
about two years ago we have made a Device basked on SDK 13 with S132 4.0.2 on it.
Now we had to build a newer version for our application and for this we have taken...
Hey.
I have a code for processor nrf51422 which compiles using a makefile. However, I decided to import it into a segger - with which I have no experience. For this I used...
Hi ,
I am just unable to find the FW ID for SD v7.0.1 anywhere.
I am using SDK 16.0.0 and SD 7.0.1 and would like to create a DFU package. Any of you know what is the...
Hi there,
I am trying to transmit data with high MTUs via pc-ble-driver-py. The data is sent from an nrf52840 with own firmware.
After the bug in nrfutil was fixed,...
Hi,
im trying to turn on LEDs on my custom nRF52 board. Im using LEDs on 13,14,15 pins. I config pins in pca10040.h to my LED pins, but they dont work. Also if i try to...
I am trying to set up multiple ble diagnostic type services for different sensor devices, from a single nrf52840. The services share a common base id and some have the same...
hi! I'm trying to use the following to configure the GPIOs in nRF52DK for the LED blinky.
nrf_gpio_cfg_output(pin_number)
But I'm not sure what number should I use for...
