Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi,
I am trying to use the p21 reset pin as gpio but it is not working as expected. it is showing a 3.3v even when i am trying to toggle the pin. I have removed the CONFIGURE...
Hello,
I am just starting to develop on nRF52840. I want to use the USB functionality. Could you please let me know how to get the Vendor ID and Product ID?
Kind regards...
Hi,
I am trying to use the bit counter to get an indication about the length of the data I am sending.
After trying around for a while it turned out the value of the bit...
Hi
I'm using S132 V5.0.0 with the nRF52832.
I tried to add an include declaration to the last added primary service by using BLE_GATT_HANDLE_INVALID as service handle...
Hello Everyone
I want to interface an external flash mx25r6435F with nrf52832. i ll be writing and reading some data. It should be spi .
Can you guys please suggest me...
Hi, everyone, We develope the BLE project on nRF51822 tool that uses the ADC. But the read measures are different from IC to IC. At the link devzone.nordicsemi.com/.../how...
Hello,
I have see this demo
.hex are available witch is already nice, but I would like to get everything needed to reproduce it.
Does someone know if it's possible...
I'm using a custom device which has two services and each of them has one characteristic. I'm using notifications to send data to the other side and on each notification complete...
Hello!
I am a huge fan of "nRF connect"! This software is helpful! Thank you Nordic for giving us this for free!
When playing with a few devices (TrackR, Thingy, non-Nordic...
Hi Guys,
I need to implement the Zigbee gateway function on nRF52840, I have download the Zigbee SDK from the Nordic website, but currently only have version 1.0, and I...
Hi,
I am trying to send accelerometer values through bluetooth for nRF52832 and SDK 14.2. I am using "nrf-mpu-simple" program form this ' GitHub ' repository and added BLE...
Hi,
I use EasyDMA with UART.
I'm in permanent reception and the received octects go directly into a memory buffer.
When the buffer is full, the writing starts again...
I have been using a JTAG to program a nrf52832 chip (SD v15) during development and am now testing firmware updates from iOS. As part of it, I've made a firmware package using...
Hi,
the default board of the homekit SDK is PCA10040.
I want to run ble_hk_doorlock_static demo on board PCA10056 , What changes should I need to do?
tool-chain :...
I am currently trying to minimize radio noise when collecting data via the ADC, on a custom board powered by a battery (when the radio fires, it introduces a lot of noise...
