Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
Hello,
Both nRF5340 and nRF7002 list minimum storage temperature of -40C. We would like to understand what environmental testing has been done to reach this storage range...
I get error provisioning key on nRF54L15 and NCS 3.0.1. I tried using "Erase all" in nRF connect SDK Programmer, but it doesn't help. Please check also the attached log. nrf54l15dk...
Hello,
I am developping an application based on PAwR (Periodic Advertsing with response) in coded PHY (S8) extended advertising on SDK 2.7.0.
costum chip nrf52840 (on...
Hi, the Nordic team
I am a novice, I now want to use the serial port and my radar module to communicate, how do I achieve this function?
I use the sdk is 2.9.1
Best...
Hi everyone,
We're reading BAT level by reading data from ADC pin and the setup diagram is shown below.
We tested our device at hospital, and we observed significant...
I am trying to populate a nrf_twi_mngr_transfer_t at runtime depending on chunks of an input file that I'm pushing to i2c.
nrf_twi_mngr_transfer_t const write_cfg_transfers...
Morning, I was trying to access https://academy.nordicsemi.com/ but the browser responded with an error `Domain configuration pending` and showed `Kinsta` node is down. Any...
Hi Support Team
We follow the guidance of the following link to program firmware to external SPI Flash of nRF54L15,but it failed.
https://docs.nordicsemi.com/bundle/nrfutil...
Hi,
I am desperate with creating my own board. I followed the example of nrf54l15dk, but I absolutely do not understand why I cannot build - not even assembling Zephyr....
Hello,
I am working on custom hardware that is based on the nRF7002 DK. The following parts are presently listed as either EOL or NRND in distribution. L6, L8: Taiyo Yuden...
I am trying to connect some I2C sensors to the the nrf9151dk and I cannot figure it out. Where do I physically plug the sensor into the board and what configuration setting...
Hello,
Hopefully this will be a quick(ish) one since I think I found the answer, but just need confirmation.
To preface (My setup):
nRF9151DK
Modem firmware: mfw_nrf91x1_2...
I am currently attempting to send HTTP requests (GET and POST) with my nRF9160 DK over an LTE connection. I have tried running the HTTP client sample code under zephyr/samples...
Hello! One of our projects will have nRF52832 replaced in EMS with revision 3 silicone and we wonder if description in is valid. It states that:
In factory state, the [new...
Dear Nordic-Support,
I have registered handlers for the two voltage level thresholds with the nrf modem library using modem_battery_low_level_handler_set and modem_battery_pofwarn_handler_set...
