I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
I am using nrf51822(128k), SD 6.0, SDK 5.2.
I found that nrf uart v2.0 app will add a "0x0A" at the end of data that I want to send.
How can I remove this?
Thank...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
I've never used Gnu's GCC before, but after 20 hours of trying and failing to install it on my macbook, I'm finding a shining hatred. I've downloaded their exhaustive list...
I migrated to nrf52 and countering some problems.
I am trying to sample 4 pins every 2ms with SAADC.
I started with Example here .
I simply changed
uint32_t ticks...
I've got a gyro I want to read some data from, but I don't know the values and can't verify if they got read correctly. When does nrf_drv_spi_transfer start to read?
i...
Hi, i;m trying to build the "nrf52-ble-app-lbs" example which i downloaded from git hub github.com/NordicSemiconducto....
I followed the instructions in the README file...
I'm thinking about changing ADC resolution during operation.
What I want to do is:
start
・Operate in 8bit ADC(normal time)
↓
・Operate in 10bit ADC(particular...
I want to use NRF51 DK to sample 2 analog signal continuously (300Hz) and send it to a smartphone using BLE.
I need advice on
Which nrf example to use to code my DK...
I've run out of space in my attribute table. No problem, I'll just make it bigger with ble_enable_params.gatts_enable_params.attr_tab_size .
The easiest way to do this...
Hello,
I am trying to implement a clean shutdown process, but running into some issues. The flow of the SPI use is as listed here:
Initialize SPI instance and...
Hello,
I`m using more or less the Nordic OTA bootloader implementation.
There is a timeout that forces the bootloader to reset, if no action happens.
Because we have...
Hi, I want to know relation about Scan interval/window, ADV interval.
I knew scanner is scan during window term.
Then, When i use central and peripheral at one device...
Hi.
I'm trying to make NRF52 write 6 bytes of data into flash and read in the DFU Bootloader.
For that purpose I choose to use "pstorage" library instead of other flash...
