Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
I am wondering what is the lowest DBM/RSSI i should have to make sure my connection between devices is safe both with setting up a connection and datatransfer?
Hello,
I know it is not recommended to use SD8.0.0 and SDK8 on revision 1 ( QFAAC0 ) based modules.. But as it is for testing purpose only and would save me a lot of time...
When not programed bootloader,my own 51822 module can work without Development Board,i supply the power through the button cell to my module.
But when programed bootloader...
Hi,
I want to use ble_app_multilink_central example for my own application. Here are my problems:
Setting MIN and MAX CONN_INTERVAL to more-less 20ms or lower (both...
Hi.
In my program I need a frequency at 2 MHz (a square wave with duty cycle at 50%), it should just run a frequency in a short time, under one second. Also the code must...
Hi,
I'm using a simple timer with interval set using "APP_TIMER_TICKS(1.4, APP_TIMER_PRESCALER)" alongside softdevice. Now i'm trying to get it to go faster but it would...
I got this error when programming the Development Dongle. The dongle is recognized in the
Master Control Panel as a COM4 - xxxx, and when is connected a green led and blue...
Hello,
We are French students in a school of engineers. We are developing a project based on the nrf51822.
Actually, we implemented RIOT OS on this SoC and we would...
I am currently using softdevice 8.0.0.
I am curious if the nRF51822 will be upgradable to be 4.2 compliant with a new softdevice release in the future? My understanding...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
I am trying to allow 2 peripherals to bond to a central, and would like to be able to use 2 push buttons to delete the bond information for either device. Is it possible to...
Hello, Nordics :)
I am trying to develop ANCS device with SDK 8.1, but I have some problem.
This are my environments.
Board: custom board.
chip: nrf51822AA...
Hi,
Function call to > err_code = ble_advdata_set(&advdata, NULL);
returns always err_code = 7 (NRF_ERROR_INVALID_PARAMETER) for a 128 bit UUID type (BLE_UUID_TYPE_VENDOR_BEGIN...
I am using pca10001, SDK6, SD7.1.
In my application i want to send a large amount of data to central(ios).
So im sending data as a packet of 19 bytes and each packet with...