Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hi.
After 3 days I've finally got littleFS working on a custom nRF52840 board. I am using nRF connect SDK v2.9.0 which includes Zephyr v3.7.99 with some additional Nordic...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
Hi Team,
Recently we did a network related testing for our CL5G modem (nrf9160) and observed a problem, in this test we used a nmap tool, this tool will search for open...
Steps to reproduce the problem
Create a new application based on the Matter Light Switch example of the SDK 3.0.2
In prj.conf set CONFIG_CHIP_FACTORY_DATA_BUILD=n
...
Hi,
I have a JLINK EDU and JLINK LITE and an nRF52 module and am attempting to use nrfjprog to program the device. Both devices are able to erase the chip, but the JLINK...
hi,
i'm new to bluetooth development so i have got a Tiny BLE. ( wiki.seeedstudio.com/.../Tiny_BLE)
the Chip is: nRF51822
i use for the development at the moment the...
Does Nordic, or any third party, provide an iOS app that utilizes the features of BLE 4.2? Specifically the larger packets sizes, and is there example code? Wish list would...
My net is a star type with many nrfL01P+ units.
Now i simply use only pipe 0 with no acknowledge (and same frequency for all units).
My question is if can I use pipe 1 ...
Hi,
I'm building a device with an nRF52 or nRF51 Module (still undecided), but still need a second MCU for USB Host functionality. Unfortunately, USB Host requires a precise...
I modified the nRF51 SDK_v5.1.0 .36092\Nordic\nrf51822\Board\pca10001\s110\ble_app_hrs proj and downloaded to my self-made pcb,and it worked well. Then I want to update to...
Hi there,
I'm using an input GPIOTE based on SDK11. The interrupt is consistently being fired. On the other hand, if I use "if(Pin_6)" to check the trigger, it does not...
I am trying to use SEGGER_RTT_printf with SDK12 in eclipse.
I have added the appropriate lines to the makefile and SEGGER_RTT_WriteString works fine.
My Makefile lines...
I followed this blog entry ( devzone.nordicsemi.com/.../) setup IAR to debug in monitor mode (by adding Jlink_monitor.c, jlink_monitor.h, jlink_monitor_isa_iar.s, add EnableMonMode...
Hi,
In our project we need to store data onto the internal flash memory.
The data that's stored will be transferred and modified via "BLE uart service". When I tried...
Hi guys,
I'm working on an nRF52832 chip (PCA 10040) with softdevice s132 (v3.0.0) and I'm facing with a big problem; in my project I use an spi (instance index 0) and an...
Hi,
we have the need to develop an application that needs a precise second counter over time.
Our firmware is using the S110 SoftDevice (v8.0.0) and SDK v8.0.0 to perform...
Hi!,
I'm trying to compile GitHub examples, for example this github.com/.../nrf51-ble-tutorial-service
I cloned it into nRF5_SDK_12.1.0_0d23e2a/examples/peripheral....
Hello,
I have custom board with nRF52832, and I want to have possibility to DFU over UART.
I tested example bootloader (nRF5_SDK_11.0.0\examples\dfu\bootloader\pca10040...
I am using nrf51 SDK v.12.1.
And I found NRF_LOG_INFO("BLINKY START\n");
where can I find this log?
Is this different from SEEGER_WriteString or something?
