Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
In ble_app_uart, the tx and rx characteristic uuid are shown below, and it supposed that the Tx characteristic enable notifications while the Rx characteristic enable write...
The hardware I am using is based on nrf51822/pca10028, with s110 SoftDevice version, and the SDK version for the project is 8.1.1 Using Keil uVision 5.21.A
When opening...
Hi,
I am running the mqtt subscriber example provided in IoT SDK (nrf5_iot_sdk_3288530).
I am using raspberry pi as router, and following the infocenter tutorial .
I have...
Hi ,
This is the first time I am using nRF52 and I don't have any experience about Antenna design. Here is my question: I am using nRF52 CIAA variant and planing to use PCB...
Hi,
I need to change advertisement data while advertising. The goal is to set new data for every packet. Firstly, I was trying to put new value like this, but it didn't...
hi all:
Recently, I develop with nrf52832, the softdevice is nRF52_SDK_0.9.0_0c82e3e.
In my application, I need a big buffer, so 32K ram can not satisfied. As the errata...
Hi all, we designed a custom board using nRF51822 now we need to test these custom boards working properly are not for these I'm creating a factory test project by configuring...
Hello Nordic Semi Developers..
I design my Product prototype using NRF52832
What is the plan of Nordic to provide SDK to support NRF52832 dynamic Mesh with
[1] Over The...
Hello,
I want to read the current ticks in RTC0, and want to measure the time elapsed after some events by using ticks to milliseconds.
Basically i want to display the...
Hello,
I need a little help regarding IoT-SDK 0.8.0 on nRF51.
What I want to achive:
Get the IoT-SDK 0.8.0 MQTT-Example running on nRF51 and publishing sensor data...
I am using nRF51 IoT SDK and nRF51-DK.
After setting up Raspberry Pi3, I ran icmp sample in the SDK for testing ping6.
when sending about 60k byte, we could not send the...
Hello, I used to think that handles are just a member of a stuct or perhaps a field of a packet, which is used to identify data payloads.
Now it seems that I might have...
Hi,
I have a problem with the nrF8001. I connected to STM32F4 and I use the nRF8001 SDK v1.7.
I need send several (less then 20) bytes from the device to the phone with...
Hello,
I used nRF5_SDK_12.1.0_0d23e2a, SoftDevice 8_9_0, the ble_app_uart_c example code.
I want to add the timer, after add the following code, my system can't work....
