Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
I'm tring to run my first twi program using nrf52. but I got complilation error no number named Power in NRF_TWI_Type
it's strange because NRF_TWI1 called from twi_master_write...
I'm building a project on the nRF52382 with the S132 SoftDevice. The project includes a Central device (GATT Client) that reads values from a peripheral device. I used the...
Hello,
I'm using the nrf51822 chip with S110. The advertising rate is 3 seconds.
I'm testing with 4 different smartphones:
Samsung Galaxy Xcover 3, Android 5.0...
I am running the NFC Launch APP example in SDK5 v11.0.0. I am using a PCA10040 dev board with the NFC antenna connected to it and testing against an NFC-enabled Android phone...
Do the GPIOs sink current even when there is no power applied to the nrf52 chip?
We connected a LED to one of the GPIOs and connected the other end of the LED to VCC. The...
hi all,
yesteryday,I download bootloader and app to my nrf52832 by nrfgo studio, but I checked the option lock entire chip from readback ,after that,I found I can not download...
Hello,
I am working with the newest revision of the nRF52 Development Kit and the app_beacon example.
I try to change the clock source for the following code:
nrf_clock_lf_cfg_t...
On SDK 11.0.0 only ( NOT the alpha release )
Do not judge the quality of SDK based on number of entries here. This thread should be considered part of Nordic effort...
On SDK 10.0 only
Do not judge the quality of SDK based on number of entries here. This thread should be considered part of Nordic effort to main the quality of the release...
I am testing nrf5 IoT tcp client example. (in \nrf5_iot\examples\iot\tcp\client)
DK side:
IP:2004::213:ddff:fe4c:6032
run as client.
2.6lowpan border router...
I'm using the ble_app_template of SDK11. but I dont have an external oscillator, so the run time freeze at ble_stack_init
in this answer , the solution is to relace NRF_CLOCK_LFCLKSRC_XTAL_20_PPM...
Hi,
I have a NRF52DK (Chip Label: PCA10040; V0.9.0; 2015.44; 682646724) and when i try to start the DK as described in the getting startet page, Step 5 failed as LED1 is...
Hi,
I am planning to make a program so that when a beacon goes far away a specific distance (around 5m) then the led should light up.
I have taken some measurements...
Hi,
I have a couple of eval boards that were created for software and hardware development. We have two versions of the nRF52832 on these development boards. I know that...
I am using nrf51822 powered by a 3.3V regulator in a li-ion powered application. We have a high current load that we're controlling with PWM at 20kHz. Radio performance is...
