I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
Hi
Regarding the NFC url example there is any way to change the URL dynamically. My idea is to, at a certain point, be able to modify the URL configured during the setup...
Hello,
I'm having an issue when trying to update the bootloader itself: NRF_UICR->NRFFW[1] returns 0xFFFFFFFF, which means I can't use the MBR command to swap bootloaders...
Our BLE product uses a meander PCB antenna similar to PCA10031. It works actually quite fine, but a question pops up when it comes to tuning.
Antenna matching design in...
I'm having some issues getting the auto ACK to work properly. I am only receiving auto ACK messages on the first 3 received packages, after which the receiver stops replying...
Hello i have a system that build in an ultrasonic sensor RedBearLab BLE Shield ( nrf8001 ) and arduino i want to get ultrasonic data via bluetooth and see it on nRFConnect...
Hi,
My host MCU controls nRF51 over SWD interface.
How can stop/halt nRF CPU? After initialization the SWD(init/read DB/AP AHB, etc.) I need to halt (stop nRF program...
Hi,
I would like to have one page of flash mapped manually to store information critical for the device. Let's assume I do not trust data preserving by DFU or there is...
I have some BLE traffic that I have sniffed and am displaying in Wireshark. Most of the opcodes (read/write request/response indications/notifications etc.) are parsed/displayed...
I am trying to develop a GATT service on nRF51.
The GATT service measures a few values, and stores them in a characteristic. When the GATT server (phone) requests data...
I am trying to build a device to stream the 9 axis sensor data from the I2C based sensor and then transmit it using BLE UART profile. It is sampled every 3 seconds using app...
I am using an nrf51422 board. I want to update via OTA using ANT+ Dongle. The device information shown in the OTA Updater is parsed from the Bootloader Code. Is there any...
Hello!
I want to connect the MCP9808 with the nrf52832. Therefor I use i2C.
My example on the nrf52832 is the:
<nRF5_SDK_v11_0_0 folder>\examples\ble_peripheral\experimental_ble_app_eddystone...
We're quite interested in producing an nRF52 design based on the solar beacon (great design, and clean software). I appreciate the relative simplicity and manageable BOM cost...
Hello,
I am developing a system that samples 3 independent data using SSADC. since the timing was important in my system, I decided to use PPI to trigger the SSADC.
However...
