Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hi,
I am facing some issues on the Android part of the BLE.
Firstly it takes around 20 seconds for the android phone in scanning mode to find the nordic board. This...
I encountered the following error while adding device manager to ble_uart_app in SDK_11 s130 using the hardware nrf51-DK. I'm using Keil compiler.
._build\nrf51422_xxac_s130...
While using the device manager, I encountered this line;
#define SEC_PARAM_MITM 1 /**< Man In The Middle protection not required. */
Since security is important, is...
Hello!
I'm trying to test several types of ANT communication like broadcast, background scanning, etc.
And When I check ANT broadcast rx example, I realized that some...
Hi Support Team,
i want to know the voltage range of AVDD(internal DC/DC output) of NRF51822 when DC/DC enabled, please help to check.
i don't find this information in PS...
I use nrf51822xxac, sdk 9.0.0, sd130. When I connect to some beacon as a central I no longer receive BLE_GAP_EVT_ADV_REPORT and I am not able to receive advertising packets...
Hello,
We do not want our beacon on at all times. I suppose our need below has been asked before.
Is there a sample snippit of code, or a document on ble_app_beacon...
hi:
i want to create timer in my code, i create timer and start the timer ,but the timer do not work,i found timer number can not exceed four,detailed information in the...
I found a bug in the FreeRTOS port provided by Nordic for the nRF52832 in SDK v11.0.0. This bug only applies if configASSERT_DEFINED is equal to 1, as the affected code is...
Hi,
We are assessing the pros and cons to port our software to work on S130. We are currently using S110 (Peripheral) and S120 (Central) on nRF51822 rev.3.
Based on the...
I am running ble_app_uart sample code on nRF-dk using SoftDevice n130. It is working fine.
Currently, when nRF UART app connects to ble_app_uart, user does not need to...
I have hard time in start a twi in nrf52832 with SDK11.0, I can't initial twi ,whatever i do ,when i build is still an error ,here is my code:
static const nrf_drv_twi_t...
Hello. Nowadays I'm trying to upload the softdevice for the RTOS based on the freertos.
As you know, determinism is very important for the realtime.
I want to know the...
Hai guys,
I am using nrf51dk, S130, and Keil to develop a simple project. My aim is to send the sensor data from the nrf51422 to the mobile app.
when no mobile is available...
I read this thread: nRF51 beacon high frequency scanning and advertising and have similar problem here.
Some repost from my electronics.stackexchange.com question
...