In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
I have an application programed on the nRF 52DK (PCA10040). Its a UART communication to a distance sensor. The Problem is, that I cant send anything from the uC to the Sensor...
Hello,
I just run in following issue. I try to configure an UART to send some bytes. To check the configuration, I just let the program loop, after the sending. Attached...
Hi all! I have a smart beacon kit rev 1, with s110 on it (the latest firmware available). I am using the RTC with the 32 kHz crystal (50ppm) to trigger an ADC conversion every...
After releasing reset to the nRF51, its UART is responding with
RX: A4 1 6F 1 CB
Further requests for things like capabilities, etc go ignored, and opening a working...
hi all,
i cant able to find the version 11 softdevice hex file. can you please send the link.
and can i use the version 8 softdevice for version 11?
-Thanks in adv...
In the migration guide, I can read: "Clearing an interrupt event may not take effect immediately."
And an example of required code is given as:
NRF_TIMER0->EVENTS_COMPARE...
I'm creating a PC application using the ble windows driver by nordic, i cannot implement white list. I ported my code on the firmware & it works.
Is this a limitation of...
When i follow the Getting Started guide for the nRF52 DK at point 5 the led (led 1) does not start pulsating and I do not get contact with my phone. I tried to upload the...
I am trying to make communication between STM32F407ZET6 and NRF52832 chipsets using an SPI interface.
One is master and another is slave. If I take NRF chip as master,...
I am noticing a problem with pstorage_raw_clear when called in the DFU code. My problem is this: when attempting to update an application, if the application is too large...
HI, I have a remote control with nRF24L01. It was talking with Gen1(uses nRF24L01) product via ESB. Now, I am developing Gen2 product*using nRF51822xxaa) and I need to support...
Hi,
i'm doing my own bootloader and i want to use external flash to download image trough a spi. The bootloader project based on example from SDK11, now just an external...
Hello:
It appears (although I am not 100% certain) that there is a small delay (< 10 usecs) between EVENTS_END in the radio and MICSTATUS in the CCM. I believe I have read...
Hi,
I've got an application running on an nRF52, and it's calling sd_app_evt_wait() from the main loop - and it's staying in that function pretty much all the time.
...
I don't have a 32KHz crystal on my board (using the stock Rigado module) and power isn't an issue as the board is mains powered in operation, so I was intending on using the...
