Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
hello all,
i am a begineer to nordic . i am trying to read adc PCF8591 value through TWI and i want to print the value in UART TERMINAL.
i have written the code. but...
Hi,
Im trying to connect ble_app_uart to my gsm module. For some reason program fails at runtime. I was expecting to find a filename and line number where the error has...
Hi,
nRF52 Board, S132. Now, I want 6 pwm, 6 adc .
nRF52 has 5Timers, Timer0-Timer4.
Now, I allocation these timers as follows:
//TIMER0 is used by softDevice
APP_PWM_INSTANCE...
Hi,
I want to access restricted peripheral: TIMER0.
After small research found that I should use sd_ wrappers, in my case sd_nvic_SetPendingIRQ(TIMER0_IRQn) however I...
Greetings,
I'm working with LPCOMP to detect a signal. This signal is the output of an opamp amplifier. What is happening is that when the LPCOMP is switched on there are...
Hi,
I am using SHT21 Temp sensor via TWI manager. As per the spec shown in the image
I have to add 20us delay between the sensor ACK and STOP command.
Is there any...
Hello, I have the Beacon Development board and the sample firmware downloaded and up and running in the Keil MDK IDE. My specific application requires some code to execute...
Hi,
i want to add a current time service to nRFgo. In particular for the glucose measurement profile.
Any suggestions for this???
I add manually the current timer service...
Custom nRF51822
SD130
SDK V11
So sometimes my disconnects seem to fail, the return code says success, but when I try to reconnect I get an error 18, NRF_ERROR_CONN_COUNT...
Hi,,
In the GPIOTE example code(I use TIMER2), I want to control the cc register values by accessing the TIMER2_IRQHandler routine. I tried enabling the interrupt for compare...
I found there is no ble_app_hrs_rtx PCA10040 ,
and release note said:
nRF5 SDK v11.0.0
Heart Rate Application with RTX: Support for nRF52 has been removed.
...
Hello,
I have some MDBT40 modules from Raytac that are blank. I want to flash some code (anything at this point) using the STLink/V2 programmer , SWD interface, and OpenOCD...
So I've got my device running, set up two services with some read and write characteristics and it all works like charm now.
But now I want to react to values written into...
I am using GPIOTE to response to transitions in some GPIO pins. This code is added to the BLE UART example code (ble_app_uart_c with S120) from SDK 10. The code is already...
Hello
I have some trouble with my DFU bootloader, because I changed the BOOTLOADER_REGION_START.
This is, because I need some more space for bootloader.
Do I have to...
