Hi,
I’m working with an nRF52832 DK board that’s stuck in bootloader mode—LED 5 just keeps blinking. Here’s what we’ve tried so far:
Held the IF BOOT/RESET button...
Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi, I'm updating my code which used to have a direct handler GPIOTE_IRQHandler(void), however I can't seem to get this working.
The Kiel Run Time Management has a requirement...
I updated from SDK 8.0 to SDK 8.1. My project had both app_uart and app_gpiote. With 8.1 (I don't exactly remember how it was on 8.0 and I have not spent any time researching...
I wanna use a nrf51822 dongle to sniff all data packets sent by 4 to 6 beacons, without large loss. The code I use is a python api given here learn.adafruit.com/.../python...
I need to provide a battery level in the application I'm working on. This application's services will all be custom - I'm not using predefined BLE services.
Our device...
Dear Sirs,
I am currently developing a project using nrf51422. My programs works fine with pca10026 develop board.
I builded a custum PCB for my project. All HW components...
In the ble_app_hrs_c the scanning indication LED blinks with a periodicity of about 4 seconds, while the advertising LED on the peripheral blinks at the expected 2. Both systems...
Hi,
I am currently experiencing TWI module lock-up issues with the hardware TWI library, which is supposedly fixed according to PAN v3.0, issue #56. (The issue was previously...
Hello,
For me, at the moment there are two things unclear.
With the help of some Nordic examples, I was able to add a Service with 3 characteristics to the used S120 BLE...
Hello all,
I'm new to embedded development and could use some help here.
I am currently working on our own board with a nRF51822 chip on it and using SEGGER j-link to...
Hi,
I just got my nrf51 dk and my task is to connect it with a bluetooth device, say a bluetooth treadmill, and retrieve data from it. The bluetooth treadmill was designed...
hi, i'm trying to develop a wearable health device.
actually, the device is a little unusual because it is attached to the Armpit or sole of the foot or inside knee ..
...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello
I'm trying to diagnose a problem I have with my own hand-soldered nRF51822-QFAA based bluetooth proximity device. I have the PCA10028 development kit to compare with...
MasterEmulator Version 2.1.12.6,
PCA10000 Version 1.0,
MEFW nRF51822 version 0.9.0,
The log file shows the following;
12;18:17:38.4681 [] - - Start of script: (2015...
