I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi everyone,
I bought two NRF24L01+ off ebay a couple of week ago and started to work on them this week. I seem to have problem with establishing a reliable communication...
Hi,
I use : An nRF51822 mbed kit + Kiel 5
So I updated the firmware like this : mbed.org/.../ and I dropped s110_nRF51822_v6.000 into MBED(H:)
I successfully use...
Hi,
i read about a new Chip revision of nrf51822. So i have to buy new Development Kit. How can i find out what it is the actual DK and where to buy it. I don't want to...
Hello All,
I was looking at the flash writewrite_example and the starting address is defines as:
addr = (uint32_t *)(pg_size * pg_num);
Later in the code, the example...
Is there any updated install procedure for the nRF51822 tools?
I'm trying to follow procedure in: nRF51822 Development Kit User Guide v1.4
I have the nRFgo Starter Kit...
Hi all,
In my keyboard application, I found sometimes it return the INVALID_STATE error code , when called keys_send() , once this error code appeared, no others return...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
I've looked over all the previous posts but none of them seem to work but the most useful one I can find is this one:
devzone.nordicsemi.com/.../
The code compiles fine...
Hi,
I'm trying to build the ble_app_beacon project for the nRF51822 (pca10001 board). Using default installation folders, latest SDK (v6.0.0) and Keil V5.1.0.0. I used...
Hi
I've made a small application on a NRF51422 device. It's is loaded with the newest version of S320 and the newest API from you homepage.
In my application i need...
I noticed that flash error logging was taken away since pstorage was added (sdk v5.0.0 and softdev v6.0.0.1-beta). Will it ever be added back?
If you say that it'll never...
I'm using the nrf51822. and then I tested the samples to receive the ANCS and send to iPhone information of temperature sensor.
I would like to merge the two above-mentioned...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
I have the nRF51822 Evaluation kit and put the Heart Rate Demo on the PCA10001 (V2.1.0). When I press Button 0 it doesn't advertise. I have the module (PCA10000) scanning...
