Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
Hello Nordic Team,
Currently, we are performing power consumption testing using the Nordic nRF54L15-DK development kit.
As part of this, I aim to fully disable the Radio...
Good afternoon we are updating some Nordic chips but to make the connection work it is necessary to install the modem version 1.3.1 wait for it to connect and then install...
I have a custom board using a nRF52840.
A part of the configuration is a Analog Devices MAX98357AEWL+T Class D amplifier which is driven by i2s0.
When the board is idle...
Hi,
When running the python script in attachments
By invoking it like this :
python.exe ./nrf_build.py --sdk-version v3.0.2 --project-path <path_of_the_project...
Hi, I'm working on enabling **FOTA for the application core only** on **nRF5340**, based on the **`nrf5340_audio` example**, using **only internal flash** (no external flash...
Hi, I am trying to code my nRF51822 on my custom board, however right now I'm having my doubt on using some of the example code provided in the SDK.
Essentially, I want...
Hi,
1/ I download the s110 softdevice and ble_app_hrs to the nRF51822 board, and running normally.
2/ I download the s120 softdevice and ble_app_hrs_c to the nRF51822...
Dir sir. I read the white paper "Tuning the nRF24xx matching network" and I have a question.
I would like to know the setting of the spectrum analyzer when I measure the...
I'm looking at the 5.2 SDK and I have noticed a few minor things that may be bugs or might be my mistake but here goes:
In the GCC linker scripts, I was carefully...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hi,
I am working on a keyboard project,I change the HID report as follows
0x05, 0x0C, // Usage Page (Consumer Devices)
0x09, 0x01, // Usage (Consumer Control)
0xA1...
Hi,
How does the advertisement filter policy work?
I tried both BLE_GAP_ADV_FP_FILTER_SCANREQ and BLE_GAP_ADV_FP_FILTER_BOTH, but this doesn't restrict other devices...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
I just purchased an mbed developer kit and I am looking for the source code for the device. I want to write an iOS app to interface to this device via BLE. I'd like to have...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Using ble_app_hrs running on a PCA10004 (nRF6310 motherboard + PCA10004 which uses a PCB antenna), the achieved range at +4dbm (<10m) seems to be short. Master Control Panel...
I think the new MCP might have a bug somewhere. I have not been able to find out the exact sequence on how to provoke it, but I have to restart the application more often...
if I set BLE_GAP_CONN_SEC_MODE_SET_OPEN, I can get data,
but if I set BLE_GAP_CONN_SEC_MODE_SET_ENC_NO_MITM,
Three different even sequences happened, only one sequences...
Hi,
I disconnect the BLE by calling *sd_ble_gap_disconnect*(), and found that it run to *app_error_handler*() after the BLE_GAP_EVT_DISCONNECTED event occured, and I don...
