Hello
I'm currently mounting a LittleFS partition in the internal flash of my Nordic MCU. However, since data is saved regularly to this partition, I’m concerned that the...
Hi! I’m currently implementing a hook using mcuboot_status_change() inside MCUboot. I’m following the path defined by CONFIG_MCUBOOT_ACTION_HOOKS , and I’ve confirmed that...
Hi,
I'm working on a customized version of the nRF Desktop App running on an nRF5340 . In my use case, I want to connect Bluetooth HID devices (mouse and keyboard) as input...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
Currently I can upload new application firmware smoothly (I use the dual bank setup). However, I have to use packets of size 20, so this takes a long time.
Is there actually...
hai ,
i am using the NRF51822 development kit. The NRF51 dongle i have used as a sniffer and a master control panel. Is it possible to load and run a s130 softdevice and...
Hi, I'm trying to estimate the nRF51422 current when running ANT. Does the softdevice use the RTC (LF oscillator) when in wait mode to save energy? Thanks
The Segger programing interface works. The virtual com port appears on my PC (COM5). The problem is that there is no board listed in the Motherboards section of the Device...
Hello,
currently I try to implement a GATT server on a nrf51422 with the s310 Softdevice. For testing I use the LightBlue IOS client on an ipad. I can see my GATT server...
I am creating an Apps which will give me a list of the running Apps in the background and foreground.
Hence Using XCode, I want to programmatically detect
List of Running...
I have a Arduino board and I want access to Ant Stack by UART. I flashed S210 in my nrf51422.
I try connect the Arduino RX/TX with TX/RX (P0.12 / P0.13), but none. Also...
Hi Nordic,
I'm wondering if I can use IAR Workbench to download SDK for nRF51DK rather than Keil. I want to develop a beacon that uses Bluetooth Smart. Can I do that in...
Hi,
Does the .hex file for V7.1.0 include the master boot record? I'm writing a JLink script to flash it and I'm trying to figure out, once converted to a binary file,...
I have the PCA 10028 Board. I would like to add a characteristic on an already existing service.
In the nAN-36 I see, what is necessary to set up service and characteristic...
Dear Forum,
I just unwrapped my new nRF51 DK board and already played with some mbed example programs which worked beautifully! So first of all - thank you Nordic & mbed...
What capacitors would you recomend for this 16MHz Quartz http://www.jauch.de/ablage/med_00000848_1411137106_JXS32-180914.pdf to ensure 40ppm frequency tolerance for nrf51822...
I read the following but was not able to use it to resolve my problem.
devzone.nordicsemi.com/.../
bootloader.hex
bootloader_settings.hex
The bootloader address...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hello,
I would like to use the PCA10031 Dongle as the peripheral with the multilink examples. I will be wiring up a button to the available GPIO and using this for a space...
