Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
Hi All, I encountered an issue while trying to use both Bluetooth and ESB in the same application. To clarify upfront: I am not using these protocols in parallel. Also, I...
Hi Nordic
Is the command:
nrfjprog -s 820100511 --qspiini Qspinrf54l15.ini --qspichiperase --program nrf54l15_FILES.bin --log
We did use it for nRF52840, where able...
I didn ' t use an external 32 . 768 crystal , the internal NRF_SDH_CLOCK_LF_SRC 0 I used。
NRF_SDH_CLOCK_LF_SRC 0
NRF_SDH_CLOCK_LF_RC_CTIV 16
NRF_SDH_CLOCK_LF_RC_TEMP_CTIV...
Hello, I am currently developing a testing software to verify whether all the pins of my module have been properly connected. I configured pin 1.03 as a high level in the...
Hi,
I am currently developing an nRF54L15 module.
During the evaluation, I measured the Tx current consumption and got a result that was 2mA higher than the value listed...
Dear All,
I updated Toolchain and SDKs to last version v3.0.2 and I'm going to add build configuration as suggested here How to create and build an application .
My board...
Please refer to the link below. How can I configure the Commission Flow according to the requirements?
www.matteralpha.com/.../how-does-matter-qr-code-work
Hello
I'm currently mounting a LittleFS partition in the internal flash of my Nordic MCU. However, since data is saved regularly to this partition, I’m concerned that the...
Hello DevZone,
For some reason, some customers didn't want to add an external flash on their module. So I advice them to use MCUBoot SerialRecovry single bank DFU.
I modified...
NRF52840
S140
APP based on ble_app_multilink_central
1 PCA10056 as central, 1 PCA10056 as peripheral, the cantral can find the peripheral and buid connection.
But...
There appears to be a bug with commenting in prj.conf. If I do this:
# This is the appearance of the device from the BLE SIG Assigned Numbers List (384 is general remote...
Hello,
I'd like to ask if or how is possible to set Thingy:91X as a Wi-Fi STA or AP? I found some examples for Wi-Fi but Thingy:91X wasn't in device list to choose. Could...
Dear Nordic,
We’re working on a Smart Door Lock project built on custom hardware that includes an nRF5340 and several other controllers. For firmware updates, we’ve adopted...
Hi there,
I am currently trying to program a custom PCB equipped with the BMD-380 that has the nrf52480 inside. Sadly, I am now stuck for days with the same issue: It...
Hello Nordic Team,
Currently, we are performing power consumption testing using the Nordic nRF54L15-DK development kit.
As part of this, I aim to fully disable the Radio...
