I've got some timing-issues with the nPM2100. As I could not locate the relevant information in the datasheet, I'm requesting this here.
My PCB has an nPM2100 with a mechanical...
Hello
I’m aware that this topic has been discussed in several posts from a couple of years ago, but I haven’t found a concrete solution yet.
I'm currently using an external...
When my peripheral calls sd_ble_gap_phy_update, setting rx_phys and tx_phys to BLE_GAP_PHY_AUTO, I receive the BLE_GAP_EVT_PHY_UPDATE event with a status of BLE_HCI_UNSUPPORTED_REMOTE_FEATURE...
Hi,
I recently checked support of MCUBoot validation and from NSIB for nrf54l15. (sdk 3.0.0 and above)
During this, I enabled Signature algo as ecdsa-p256.
And...
How to prevent storage partition from erase durning MCUBOOT firmware update?
I use Settings with NVS to store data
CONFIG_FLASH_MAP=y
CONFIG_FLASH=y
CONFIG_SETTINGS...
Hi,
I am building a Thread network ( www.youtube.com/watch with a Rasp Pi 4 as a border router, an nRF52840 DK as an RCP, and an nRF5340 DK as a child to be added into the...
Hi,
I have pca100000 v 1.0 and v 2.1.0, and the master control panel application with the latest version of 3.5.0. The firmware we have flashed on both the dongle is 0.9...
Hi,
How can i run the nRF utility application using my Nexus 4 smartphone? After installing the application it is showing that device is not supported.
Regards,
Bala...
Hi,
For power critical application, i know that ,we need to enable the peripherals whenever we need that.
After we need to disable by using ENABLE register.
My question...
i'm testing in my pcb. i designed a nrf24le1f board (the guidance of the datasheet). But i transmitted not far, about 2-10cm a long. I don't know i wrong in design pcb or...
I have the nRF Loader app installed on an iPad Mini. I have the dfu_dual_bank_ble firmware from SDK V5.0.0 and SoftDevice V6.0.0.1-beta loaded on my nRF51822.
The app is...
Hi all,
I am in the process of debugging the ANT broadcast_tx example program using Keil on nRF51422.
I have flashed the program on nRF51422.
After entering the debugging...
I have nRF51822-EK
I am not sure whats going on with it.
I can run LED blinky example nicely ( no surprise :D )
But when I try to run softdevice examples like heart...
I have used TI Code composer which is based on Eclipse, and they created a specific Target menu option which allows resets and other target specific items.
Is there a CDT...
Hi,
I use the UART to do the device firmware update and have used the dfu_dual_bank_hcl to compile.I use the nRFgo Studio V1.16
to program the s110_nrf51822_5.2.1_softdevice...
I've downloaded the latest SDK and soft device. I've been able to compile the ble_app_ancs project, run it on my dev board and even connect to my iPhone. Although I'm getting...
Hi everyone
I'm using the nrf51822 connect with stm32f103 through UART,it's current is >1.9mA,is it normal?
I have full reset to disable the debug interface,it can...
Hello developers,
I've got an nrf51822 EVA kit with on it the QFAACA chip. KEIL v5.0.5, J-link V4.78, nRFGo Studio V1.16 and nrfGo SDK (zip) V4.4.2. The Softdevice on the...
when I enter the system off mode then used a GPIO to wake up the IC, the "RESETREAS" register show "Reset due to wake-up from OFF mode when wakeup is triggered from the
DETECT...
Hi,
I have only nRF51822 DK without starter kit motherboard. how can I download softdevice(S110 Bluetooth low energy stack) to my nRF51822 chip in the Keil environment?
...
