I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello,
I need example code or guidance in how to receive eddystone advetising packets on the nRF52832.
In my project, I can send standard eddystone packets to a app...
Hi All,
I am new to BLE technology and I am working on nRF52840 and I have below queries.
1) I need to operate my device to scan and advertise both at the same time when...
I stuck a breakpoint in the main loop to capture the timer values. Everything looks good, the capture has worked. The interrupt isn't called however. I've disabled the softdevice...
Please understand my low English level.
Segger cannot find be_advdata.h. I've added this route to the preprocessor. But an error occurs. How can I fix this?
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
For better clarity, I am trying to understand...
When scanning, is there a built-in way to detect and ignore duplicate advertisement packets (i.e. from the same device)? Specifically, I want to instruct the SoftDevice not...
Hi.
Thank you for your hard work.
I would like to apply the Timer example to the Uart example in SDK 15.2.0.
It was able to build without any problems before the timer...
Can somebody help me to setting up debugging in eclipse (nRF52840_xxAA)? As all I use some old tutorial here . But I still can't set up debugging on eclipse for 3 years of...
Hi
We are using the nRF9160 to drive the SD pin of the QM14501 LNA, which would typically consume 740uA. While the pin is driven high, I only measure 0.7V on the pin, so...
Hello,
I'm receiving a FDS_EVT_UPDATE (FDS_ERR_OPERATION_TIMEOUT) in my fds event handler. My update didn'it work but i don't know why.
If someone has already faced this...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
hi, I am beginner , so confused how to doing write and read sequence. I want read and write sequence with register setting .please give me how to develope logic for that.
Hi,
I'm working on a BLE link between two dev kits. For the time being, both have USB drivers and handlers that will pipe data from one USB terminal to another over BLE...
I'm having a bit of trouble getting a program downloaded onto my development board. I've been using Keil 5 to program and I haven't had a problem until I started experimenting...
