Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
i have purchased one of the modules. i need to interface with other modules of the same kind but how will i start programming it ,can u people suggest me the IDE ? do i need...
Hi,
I try to modify 51822 device_firmware_updates code for 51422.
But I have a problem.
When I run my code, my cell phone can connect to 51422. I can click DFU button...
According to Page5 of nWP-018, if we compare QFAA G0 to C0, G0 doesn't have a valid version reference design with the right balun. But G0 and C0 have the same valid reference...
Hi there,
We're looking to use the entire 16 KB of RAM on the nRF51822 when the S110 is disabled. We've come across an odd case, where doing this:
memset(0x20000004...
Hi there,
I am trying to learn how to develop for the 8001 chip on an Arduino board.
Does anyone know a good tutorial I can use to get to grips with how i would go about...
I have nRF 8001 BLE chip.First i want to know will this chip contains any Firmware i.e it has its services and characteristic or not? And i want to write my own Services and...
Dear Sir,
I used nRF51822, I found sometime the program reset itselft. Then I made a test program to send out the "RESET REASON"by BLE message. I found the reset reason...
When a callback function is registered via the softdevice_ble_evt_handler_set(), are there re-entrancy issues when the callback is called by the softdevice?
For instance...
HI,
May I ask question ?
I am testing the "ble_app_hids_mouse" program . When I run the program ,but it can't pair with my computer(windows 8.1).I don't have the nRF6310...
I want to connect my mouse to win7 or XP PC(but I can only buy CSR BLE dongle CSR8510A10),
It connect OK in win8 with the same dongle but report error as the title describe...
Hi,
I have a problem is that I use the 51822 as a reader to read the 24l01's radio data.Now,I use the UART to read the instruction from the PC. If the instruction is "ON...
Hi,
I use the nrf51822 to read the data from the tag which designed by the 24l01p radio module.In the whole progress, first of all, the reading module read the instructions...
I have interfaced nRF 8001 with Arduino through MISo,MOSI,SCK etc pins and it is connected successfully. When i connected my arduino with pc, i thought nRF 8001 will start...
I'm trying to make a simple BLE app based on LED button demo (BLE_LBS.C) that probably don't use much resources. I added FIFO UART communication routines and when I tried...
