Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello,
I am trying to merge NUS client (ble_central>ble_app_uart_c) with Multilink central program (ble_central>ble_app_multilink_central) such that the central (nRF52832...
Hello,
I have a problem in the step of Secure DFU. I use nRF connect application to connect the BMD-350-EVAL and when i selected the device and start scan the "DfuTarg...
Has anyone tried to update the github project nrf52-ble-image-transfer-demo to work with SDK 16 / SD V7.0.1? I copied the main code in the project to ble_app_uart example...
Hi!
We are interesting in extended adv support, as periph and central role to establish connection in phy coded.
I've read another topic that it doesn't have PHY_CODED...
Alright, I'm starting to question my sanity on this one. I am currently trying to use the TWIM driver nrfx_twim.c to access a TWI device. As usual, I did the checks for the...
I am facing an issue about using CMOS battery for NRF52832. I hope this CMOS battery can serve mcu (in low power mode) for at least 1 year. In low power mode, I just want...
I am using a BMD 349 module based on nRF52840.
I am interfacing with AT25SF041 flash memory.
I am using SDK 14.2.
I am writing a byte to a specific address in Flash...
I recently purchased a Thingy:91. Initially it would not connect to the local network. I purchased a a J-Link programmer and via the nRF Connect Programmer updated the modem...
Is it possible to Read the battery status and/or the temperature value from the nRF52810, write that data to on chip memory, and run a code to modify the Major and Minor values...
To the kind attention of Nordic support team,
after some months I gave a look to the segger toolchain configuration for the device host example using the secured gazell...
Hi
I am trying to set up my visual studio to communicate with my nordic device and found that PC-ble-drive can help me with this.
I followed the steps mentioned in the...
HI I'm currently working on measuring distance between two points with two nrf52840 modules with the example "nRF52-ble-long-range-demo" (you can easily find it in github...
I have configured "nrf 52 DK" to worked as BLE sniffer. I am trying to sniff the data packets exchanged between two TI CC 2650 devices (in which one is master and other is...
I am trying to configure my nrf 52 DK board as BLE sniffer. I am following this blog " https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nc_programmer%2FUG%2Fnrf_connect_programmer...
Hi,
I'm using the Light Switch example and would like to read out the own address on a light switch. Is there any application call, such that the stack returns my own...
