Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello:
I am using nRF Connect v3.3.1 programmer to flash nRF9160 and got an error.
Silk on nRF9160 is: nRF9160 SICA B0 191601
Programmer can't recognize nRF9160 after...
Based on 52832, sdk15.3 running ble_app_hrs example, requesting MTU through nRF connect, the first success, the second time is unsuccessful, the app prompts Error 4 (0x4)...
Is there an application note or single set of instructions on how to get debug/log output via the SWO output rather than RTT or UART. Both of the latter are simple switches...
I'm trying to hook up a nRF51 to two other devices. One is connected with UART and the other through BLE (NUS).
The connection with BLE is working fine. But as soon as...
I am using "ble_app_hrs_rscs_relay" example. I am not able to set the TX power of advertising and scanning both. Currently the avg current is too high.
I also tried using...
Hello, in my travels through Nordic development, somehow I am only now creating truly custom characteristics, and I realize I have no idea why there is both an initial and...
Hello, when I run the subject example and connect to it, I see the RX and TX characteristics like I'd expect.
However, I see a descriptor on the TX characteristic which...
Hello! I am trying ZigBee multi_sensor example.
(I had a question here as well. Thank you. "Zigbee multi_sensor example has not connect" https://devzone.nordicsemi.com...
I want to set up a SPI transfer so the transfer itself is triggered by PPI. The PPI is set up working, the chain of events is
Timer CC0 -> Set CS low
Timer CC1 -> Start...
In implementing the --application-version-string with nrfutil I found the help was inconsistent with the application.
The help for this option is:
In the example 2.7...
Hi guys.
I'm trying to merge two projects ble_app_beacon and nrf_crypto_aes_cbc_with_padding.
I used nrf_crypto_aes_cbc_with_padding as base, copied it to another folder...
hi
i want to develop a keyboard that can communicate whith pc by ble and 2.4g . now,the 2.4g's communicate between nrf52840 and nrf24lu1p is achieved by project gzp_desktop_emulator...
I am based in Hong Kong. I purchased NB-IoT sim card with "Three".
When using LTE Link Monitor, (with at_client) I can connect to the NB_IoT network, as Three support told...
