after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello,
How can I directly read out the POFCON register value on the Watch Window while debugging?
Where is it actually located in the library(sdk 14.2) source code?...
How can i know how much time the microcontroller spends in the timer_event_handler() function? I am fear that i have written down to much code into that function. Regards
Hello,
I have the following statement in flash_placement.xml:
<ProgramSection alignment="4" keep="Yes" load="Yes" name=".nrf_queue" inputsections="*(.nrf_queue*)" address_symbol...
Hello.
I have two nRF52832 (central and peripheral). Connect the central and peripheral and call sd_ble_gap_rssi_get() on the central to get the RSSI and channel. The attached...
Hello there!
At this stage of the product development cycle, we would like to be able just to take simple reading from ADP536x module (to read either battery percentage...
Hey all,
For new minor revisions (1.X.0), will they eventually be supported by telecom's that are currently running with lesser versions? For instance, the current modem...
Hi,
I am using nrf52832 with icm20948 (I2C) on custom board and I am using icm20948 for angle measurement. For custom application I added some features i.e, before reading...
Hi,
We have preloaded the module test board with the DTM test from NRF5_SDK16.
The lab is requesting for the driver to pull up the testing interface and instructions...
I am exploring nRF52833 in a project using DK and Keil IDE. However, I keep getting errors when I attempt to download DeviceFamilyPack, etc. This error only occurs if I try...
Hi,I have a problem.I used three channels of ADC sampling in the project.If I connect the ADC port directly to GND,the ADC value of the sample is not equal to 0.But if I change...
hai ,
In my application , my nrf52840 device in peripheral mode to connect with central (ESP32).
then if i get a mac id from central ,i need to connect over with central...
Hello,
For my project I use uVision v.5.23.0.0; now I am willing to prepare two different targets using the same source files: one target for debug, with included the drivers...
Hi,
I am using nRF5_SDK_15.2.0_9412b96 SDK and dev board - PCA10056 V1.1.0 2019.22 - 683524107
USB serial driver is not detected on Windows 8.1 Pro while testing my customized...
