I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
I am developing a NIR (Near-Infrared) product using nRF52810. I use 15.3 for SDK and S112 for Softdevice. I implemented ADC (saadc) function based on ble_app_uart.
I have...
Hi everybody,
I been experimenting with the HID over GATT example (mouse), and I am trying to use more than 3 report IDs. When I used only 3 there's no problem. But when...
Hello DevZone,
SDK 15.0.0. SD132 PCA10040
SPI settings : Mode 0, MSB first, 125kbps, orc = 0
I am trying to get NFC communication between two dev kits, one using the...
Hi,
is there a possibility to tune the external xtal (lfxo) or the rtc?
In other microcontrollers there is a possibility to trim, for exampe the rtc ignores one or more...
Hi teams,
I have build custom board connected to ethernet via ENC28J60 ethernet controller.
It uses SPI communication with ENC28J60, but some strange behaviour during...
hello
i am using nrf52832 with pwm driver (working with ble and s132 if it metters)
i need to control 4 different motors speed via pwm, since there can be only 3 instances...
Hi
I have implemented a scannable advertising on nRF51822, s130, SDK12,
I can see it's working by reading the scannable information on nRC Connect, however,
on the sniffer...
Hallo,
I have a question reading the datasheet. It states:
" If a regulator is only to be used in LDO mode, the inductor for this regulator is not needed. "
I want to...
Hello,
i'm trying to understand how nrf52 and softdevice work to use it in the future, i'm working on STM32 and i have my own RTOS, i try to appropriate the platform by...
I received my NRF52840 dongles and downloaded SDK 16.0.0 and SES 4.52c. I found some old documentation that said how to convert ble_app_blinky to the dongle but then exploring...
Hi,
I have nRF52840 Dongle(PCA10059), I try to develop on the nRF Connect Desktop. But this dongle can't update firmware on the nRF connect desktop.
My operation below...
I’m using the latest version of the modem 1.2.0 and sdk v1.2.0
For the most part AWS FOTA seems to be functioning.
However it will start the FOTA job and hang and fail...
Hi everyone,
I need to set up a timer using the RTC. The default function that converts ms to ticks APP_TIMER_TICKS() accepts only milliseconds. So, I wrote my own conversion...
I want to interface Client Sensor over UART in light_switch_client code. Can you please give me the idea,how to do it.
I am using Mesh_V4.0 and SDK 16.0
