Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Hi Team,
We are using nRF9160 DK, we tested that asset tracker application, that was working fine, We also tested the aws_fota (firmware update via AWS) that was also...
I want to develop a mesh network where I can send/receive data from one device to other devices(sleepy sensors) through relay/router node (always on).
For example
A (Publish...
Hi, engineer:
I need to compute FFT on nrf52840, I used sdk-demo fpu-fft, I tested the FFT operation time and found that it took 2 ms，That`s a long time, Did I configure...
Dear all, I have a problem with nRF52811 GPIOTE input interrupt. I have one sensor interrupt pin at GPIO P0.30 with external pull down resistor. I am able to config P0.30...
Hello community,
I have programmed my dongle as beacon. Now I want to stick them to the wall for experiment purposes. How is it possible to power them up via external...
Hello
I am considering a product that connects several NRF52840s to a USB 2.0 7-ch HUB and works with 30 BLE devices. When reviewing a product like this, there are some...
Hi everyone,
I have one question just for confirmation.The available analog pins on nRF52840 DBK are those provided by header P2 (six in total)?
Are there any more available...
Hi,
I'm working with NRF52832 in a BLE mesh project and I'm a newbie in this filed.
Project description:
- There're 5 devices in a BLE mesh network.
- In each device...
Hello,
in the corse of implementing pairing / bonding on top of the softdevice, I was looking for examples. The only example I've found, that seemed to not use the peer_manager...
Hi,
Currently i am developing BLE communication software for Android and iOS
This software is under Ionic development.
Is there any solution for Ionic/ Javascript development...
Hi !
When i try to open gps sample and enable SUPL client support with CONFIG_SUPL_CLIENT_LIB=y, i received this alert so i cant import project file:
I already have...
Hi all, I am working on light switch example and I want to perform different LEDs have their own switch, i.e. button 1 control LED 1, button 2 control LED 2. The problem is...
Hello,
I am working on a project where I can have Voice over IP on the NRF9160 DK. I am now working with a I2S microphone ( https://www.adafruit.com/product/3421 ) at the...
Hi,
I am setting a nrf52832 for an OTA DFU using BLE. I am on windows.
After managing to run the Secure DFU Bootloader following the getting started , I am trying to merge...
I'm using s140_nrf52_6.1.1_softdevice and nRF5_SDK_15.3.0_59ac345 on a nRF52840.
We are trying to verify that, indeed, we are successfully entering and using coded phy mode...
