I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Sir,
We finally added WIFI to NINA B302, using a NINA W102 coprocessor!
https://github.com/khoih-prog/WiFiNINA_Generic
Please, enjoy!!!
Here a portuguese BLOG...
Hi All, I have a question regarding modem DECT phy API. There is a function nrf_modem_dect_phy_event_handler_set(nrf_modem_dect_phy_event_handler_t handler). I'd like to know...
Nordic TS,
I've installed and begin to experiment with the DECT NR+ v1.1.1.0 FW. Initially, I'm noticing on obvious difference in the behavior of the dect_hello sample between...
nRF52832 custom board + NCS 3.0.1
We are using the Zephyr driver for LIS2DH sensor in "any motion" detection mode, which triggers an interrupt when acceleration exceeds...
Hello,
I'm evaluating the nPM1300 for a battery powered project. What is the quiescent current of the LDO? And is there an output current vs dropout chart?
Thanks
Hi, Using NCS 3.0.0 it would appear that the function sntp_simple_helper does not work with SYS_FOREVER_MS as a timeout value.
Problem: When we pass this value as a timeout...
Hi,
I want BLE and ZIGBEE to be able to switch dynamically during running.Only one mode(BLE or ZIGBEE) is running at a time.If switching from zigbee to BLE, how do I turn...
I have implemented DFU functionality in my Bluetooth mesh project and used device A as the distributor and device B as the node to be updated. I have already configured both...
We have our firmware developed with ncs2.7.0 and everything works as expected. However, with a recent effort of moving to ncs2.9.1, the same project can be built but during...
Hello
I'm currently working on writing some specifications for a future product. In this product, I want to use the advertising mechanism to send specific data from one...
we don't seem to have power numbers for the 54L, but in the 5340 datasheet it shows the LFXO (0.16uA) used less power then the LFRC (1 uA).
Is that true with the NRF54L...
Hello, I am working on a project using a custom hardware configuration based on nRF5340 and nRF7002 similar in configuration to the nRF7002-DK, except without the on-board...
Hi!
We're building a project for the nRF54 where we want to run an external library on the FLPR core.
Right now we have a prototype PCB with a module from Fanstel on it...
Hello,
I am using configUSE_TICKLESS_IDLE with RTC2 setup for FreeRTOS tick, occasionally I am seeing the asserting in task.c at line configASSERT( ( xTickCount + xTicksToJump...
Hello everyone,
I’m fairly new to Android development and currently building a BLE app using Kotlin in Android Studio. So far, I’ve managed to implement scanning, connecting...
