Hi,
I recently found out about the Periodic interval feature on GRTC CC[0] and it seems like it would be quite useful for my application. Most of my code so far uses the...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
I have a ready hogp struct and I'm trying to subscribe to an input notification (I'm connecting to a bluetooth keyboard) and I'm getting error -22. Here's the callback in...
Hello,
I am trying to count pulses on nRF52840 DK's pin for measuring water flow with hall effect sensor. I tried to implement PPI + GPIOTE + TIMER in counter mode, but...
Hi, I am using nrf52840-based custom hardware and have an external flash connected on SPIM3. Till now I was working with my other peripheral connected on different buses and...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
I am developing a device based on nrf52840, this is peripheral. But I want to change the code so that I can only connect to my device using my application (in other cases...
Hello,
As I am using max30003 ECG with nrf52840 Using NRFX_SPIM example code( SDK15.2-PCA100056 ), I have developed drivers and I am able to read device id through my driver...
We had been using an AT&T M1-enabled SIM in one of our development units successfully for quite some time. After we upgraded that node to MFW v1.1.0, it is no longer able...
I have a custom board based around the nRF9160. I am trying to use the LTE Link Monitor to test the Modem but and having problems.
I am able to connect to my board OK, please...
Hi Nordic teams,
I'm trying to integrate the DFU function into light_switch example this days. At the beginning, I used the dfu example to update my evaluation board, and...
Hi,
Good day!
Statement of problem: In our application, we are using nrf52832 SoC to control critical components (heater). So I was suggested to use a watchdog timer to...
Hi,
Im trying " https://github.com/NordicPlayground/fw-nrfconnect-nrf/blob/master/samples/nrf9160/gps/src/main.c " gsp example to check supl(AGPS) to integrate into my application...
Hi,
In-app when you scan for device and after it is found you press the connect and then the notification/permission to pair pops out. Our app developers are saying that...
Hi,
We are using nRF51DK for our development, we have developed Android app for Android smart phone.
When the Nordic BLE device advertising we are trying for BLE connection...
Hi guys,
I'm fairly new to this kind of stuff and I'd appreciate if someone could point me in the direction of how I would go about taking the data being transmitted by...
Hi nordic,
I am using SDK15.0 (NRF52840) to design a watch producation which needs pairing. I have a problem that if NRF52840 (peripheral ) has been paired with a smartphone...
I want to get the RSSI of a connected device. The sequence will be as follows:
int8_t *p_rssi;
uint8_t *p_ch_index;
sd_ble_gap_rssi_start (m_conn_handle, BLE_GAP_RSSI_THRESHOLD_INVALID...
Setup: nRF52840 DK nRF52 SDK v16.0.0 s140 v7.0.1 When I attempt to use the nrf_crypto library for AES 128bit ECB encryption I keep getting
NRF_ERROR_CRYPTO_CONTEXT_NOT_INITIALIZED...
'm sending a publication set message (0x03) from an iOS app to an nRF52840 board using the light server example in the latest SDK. This works and I'm able to receive messages...
