Hi I am using an nRF54L15 with an external watch crystal. I have notice that depending on the manufacturer of the crystal I have to use a different internal load capacitor...
i've noticed that the pc-nrfconnect-ppk is written in typescript (with a lot of .tsx files for visual elements)....
my understanding is that at the lowest-level the power...
I am using the `mcumgr` subsys to enable the DFU (Device Firmware Update) capabilities in a custom device that also features a custom (non mcuboot) bootloader. In order to...
Hi !
I have a peripheral that can connect to other nRF52's or a smart phone such as iPhone or android. Is there an easy way to detect a smart phone?
The best I can think...
Hello Nordic Team,
I have a working project that uses BLE to communicate with a mobile app, and I am now looking to integrate Google Fast Pair as an additional feature....
Hi,
I recently found out about the Periodic interval feature on GRTC CC[0] and it seems like it would be quite useful for my application. Most of my code so far uses the...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
Have you also wondered how to get serial IO (UART) with nRF51422-EK via the Segger debug interface?
[list=1]
[ ]Plug Eval kit in the USB port.
[ ]In Windows open "device...
Hi,
i need to stop one of my Timer at the falling edge of a Pin. So i need a gpiote_interrupt, is this right? Can someone help me how i can do this? if i write something...
I have 3 inputs I need to sample every n minutes. I have an n-minute timer that can kick off the first one, but I need to run the second and third samplings in succession...
We are creating our own dev board.
What pcb parameters were used for the PCA10004-nRFgo PCB antenna radio module 2.0?
1.6mm?
1oz Cu?
impedance control?
I have not...
Hello,
We want to use the J-Link Needle Adapter for nRF51822
The attached (capture.jpg) is the pinout from the J-Link Needle Adapter datasheet.
the attached (capture2...
Hi,
I have a wired problem with the nrf51422,
I'm loading the code using the J-link into my board or the evaluation board (PCA10007) that I have, the code runs perfect...
Hi all, I met a problem with measuring lithium battery voltage. I used 1Mohm and 250Kohm divided voltage, and used the internal VBG voltage as reference, and used ADC0 as...
I'm using a nRF51844
I'm writing my own ADC reading routines because I can't find any examples, but I know how to code so that's not a problem. I just want to confirm something...
Hi,
does a code example or app-note exists that describes how to configure the SPI peripheral to use an ISR to transmit data to a SPI slave?
Thank you in advance!
Dear
Do you know of a "present" /not present" low cost 2.4 GHz RFID chip for static asset monitoring in WiFi environment. compatible with, and actively associates with 802...
I am trying to hook up nRF8001 to TI MSP430F663x via nRF2740 module.
All inputs seems to be controlled properly.
Once I release the nRF8001 RESET line, RDYN goes low...
Hi,
I have a simple battery powered remote control device with a NRF51822 and using the Gazelle protocol for communication with the host.
To save battery the MCU goes...
The last few weeks I'm working with the nRF51422 and run in to several TWI/I2C issues. All of them I could solve except an issue with a SAA1064 7segment display driver from...
We have a custom board with nFR51422. Of the first 4 prototypes only one works correctly. This indicates that the PCB is ok. One difference is the chip marking. The working...
