Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
We build a new board based on nRF52833 wlcsp,
I tried to run a simple code with BLE peripheral (ble_app_uart example), and I noticed that the HFCLK is not working...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Hi
I am running this example from SDK 15.2.0.
I am trying to figure out how the server knows at the end of the session how many bytes of data the Peer received.
Anyone...
The information on the website currently only supports nrf52840.
Can nrf52833 support DFU over USB?
If yes.Which example can be used? Does it use the same DFU USB bootloader...
Hello, I am studying the peripheral/ble_app_uart and peripheral/ble_app/template examples to understand the proper way to build a peripheral with our own set of services and...
Hi,
I have hard time to setup west in my Ubuntu PC. It was installed, but not fully working. So I tried to uninstall and reinstall, and also one time, I may have upgraded...
Hi All,
I have downloaded nrf5_SDK_for_Mesh_v2.2.0_src and trying to build the LIGHT SWITCH example but when i try to compile iam getting lot errors attached the screen...
Hi,
We are currently evaluating nRF52810. I have a couple of queries on DFU:
1. Provided having an application, soft-device, and bootloader in memory, we have to update...
Hello,
I'm using ncs 1.2.0 and trying to compile sample projects like v1.2.0\nrf\samples\sensor\bh1749, also v1.2.0\zephyr\samples\sensor\* but all the defines for device...
Hello,
I'm trying to setup interrupt routines in SPIS1 peripheral.
I have a void IRQ function
But it seems like it never gets called
my init function
some...
Hi,
As I understand Nordic NCS now supports nRF52 development for nrf52832/40/11/10, so based on this I am trying to make a simple application for nRF5232 chip (peripheral_uart...
Hello,
I've been using http/https for some time with Zephyr, and am now venturing into using LTE/NB-IoT on a NRF9160DK board.
Unfortunately, from what I can tell, the...
Hi,
We are working on a Thread network application using nRF52840 DK and would like to interface a WiFi module to this board. We have checked the DevZone and found one similar...
Sir,
We finally added WIFI to NINA B302, using a NINA W102 coprocessor!
https://github.com/khoih-prog/WiFiNINA_Generic
Please, enjoy!!!
Here a portuguese BLOG...
Hi,
I have added the Buttonless Secure DFU service to my application so that the app can be updated over BLE. It seems working. However, the power management module must...
