[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
Hi there. I am freshman with the NRF MESH. I am working on project which I need to use the static provisioner node. The problem I am facing is how to configure multiple group...
Hi everyone.
I want to stream 12kB of ADC data from the thingy 52 via BLE. At the moment this takes around 4 seconds to do which is to slow so i would like to increase...
hi ,when develop the usb + gzll+ble hid funcation, i find that it will occur a erro when stop the ble stack in the project that have usb funcation,so i try in the project...
Hi,
I'm trying to debug CLI example contained into nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b by flashing it on my nRF52840 DK (PCA10056).
First of all I'm using...
Hello DevZone,
Currently I'm working to get the NFC examples up and running.
I'm using the PCA10040 in combination with SDK15.0.0 and SD 132
A colleague of mine mentioned...
Hi everyone,
I suppose this is a very simple question... I want to create multiple timers using the Timer Library .
Each time I want to create a new timer based on RTC1...
Hello,
I'm flashing custom code onto a nRF52840 based PCB.
I'm using SDK v15.0, SES 4.52.
On the debug window I get the following message as soon as I run the code...
Hi,
I am using nRF52840, S140 V7.0.1.
I am using Secure Serial Bootloader and able to do DFU of Application.
DFU of application
Using below command able to generate...
Hi,
I have a custom board with nrf52833 I would like to flash with custom firmware. I would like to flash this board by "P19 debug out connector" from DK.
How can I...
I am trying to port a tested program from NRF52 DK to NRF Thingy. To do the same I had changed the board to PCA20020. After I do that, I program using the NRF52 debug out...
Hi,
If the app keeps sending data at a certain rate, the numbers will skip and the software will stop.
I tried to see how much data I could communicate and at what speed...
In my situation, I want to use ble to designed a piconet which has 1 master and up to 4 slave .( upload(Slave->Master) rate is 2.2KB/s,download(Master->Slave) rate is 500...
Hi
A few questions regarding the "saadc_pca10040" example:
If I read one analog pin then what is the meaning of this matrix of values :
"static nrf_saadc_value_t...
This page shows that MPU is not supported on nRF52840: https://infocenter.nordicsemi.com/topic/sdk_nrf5_v16.0.0/nrfx_drv_supp_matrix.html
On the other hand, the following...
Hello Nordic Experts,
I'd like to add the usb hid composite to one of BLE examples. I followed link below and combined the example usbd_hid_composite with ble_app_blinki_c...
