Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Running nRF Connect SDK v2.1 targetting an nRF52840 DK (PCA10056)
I'm looking at the OTA DFU options for this SDK. The host side tool if i'm not mistaken is a go utility...
Hello,
I'm trying to integrate Mesh 4.0.0 into a program built with SDK 16.0.0 but I'm running into some issues including the correct files from the Mesh SDK. I followed...
Hi Sir,
In the datasheet of 52840, we know the DEC1 is 1.1V, DEC2/4/5 are 1.3V, DECUSB is 3.3V.
When measuring these pins, we may not get a precision value, like we got...
Hello,
I am developing an application to scanning a device continuously in nrf52832 chip. My concern is that when the device scan the other peripherals it consume a lot...
Hi,
Can you please give a brief idea which softdevice and SoC we should use as per our requirements.
1) The device should be able to connect to the mobile phone(mobile...
I am not able to build in release mode where as in debug mode builds. Even when option for release is chose , it builds in debug mode. I am using Segger Embedded studio 4...
We are using a BLE module EYSHSNZWZ from Tayio Yuden which contains the nRF52832.
using SDK 15.0.0_a53641a and Softdevice and Softdevice s132_nrf52_6.1.0
The application...
Hi,
Recently I degubbed issues on debug mode for an application on segger embedded studio 4.1.2. Now I see in release mode some kind of errors is happening, it works well...
Hi,
I need to use a custom board with old nRF51822 rev.2 (QFAAG0). The compatibility matrix indicates S110 Softdevice SD5.2.1. I found only 7.3.0 or 8.0.0 and there is no...
hello
i need a device capable to work with Bluetooth 5.2 to transmit audio
is nrf52840, nrf52820, nrf52832 or any other support Bluetooth 5.2 and has Protocol stack...
Hi community !
i put the same question here but with less explaination : https://devzone.nordicsemi.com/f/nordic-q-a/61393/mesh-uart-coexistence-communication-with-pc I...
I am evaluating if I should change to nRF Connect SDK for a new project so I have been updating nRF Connect to latest version v3.3.3
I have installed Getting Started Assistant...
Hello, We are developing a application that sends some data to AWS in some intervals(3 - 15 minutes). This application were currently being tested on custom nrf9160 boards...
Hi,
I am using nRF52840, S140 V7.0.1.
I am using Secure Serial Bootloader and able to do DFU of Application.
Now I am trying to do the same for generating SoftDevice...
