I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
For a customer I am developing a Zigbee coordinator / Gateway with the nRF52840. As hardware I am using the nRF52840 Preview Development Kit. As software basis I use the ...
Hello, a couple of get-me-pointed-in-the-right-direction questions, if you don't mind.
I plan on creating a system with an accelerometer that talks SPI to my Nordic nRF52833...
Hi!
I read that your Thread stack uses a different 802.15.4 implementation than the MAC driver. Is it possible to intercept special broadcast data packets e.g. from energy...
Hi!
I started to modify the ble_app_blinky example. I need to increase ATT_MTU, so I modified NRF_SDH_BLE_GATT_MAX_MTU_SIZE. For this, I needed to increase the RAM of the...
Hello,
I'm using Mesh SDk4.0.0 and SD v7.0.1. I have tested the light switch client and server examples.
Now I want to add some more models for additional functionality...
Hi , i want to change the device name by connecting the device using nrf_toolbox , have a look at my code , you will get what i am trying to do . By the way i am using nRF52832...
Hello Nordic!
I'm developing with nrf52840, s340, sdk 15.3.0, gcc-arm-none-eabi-7-2018-q2 in my customboard.
Recently, I am making ble central module.
I can scan and...
Hi, I have only one question: during the write or erase cycle using fstorage, the cpu is locked? Sofdevice, Interrupts and main application are working also during with flash...
I'm using FDS together with Flash manager, and checked if everything goes alright in flash.
As per doc, I set FLASH_MANAGER_RECOVERY_PAGE_OFFSET_PAGES to FDS_PHY_PAGES....
Hi, I just try to start with the spi master example (nrf5sdk/examples/peripheral/spi) on mus PCA10040 board. I'm able to compile&flash it. It seems to be running (LED1 is...
Hi ,
I working on the getting started assistant setup but got failure when verify the GNU ARM embedded setup , see the following log :
11:32:05.867
c:\gnuarmemb\bin...
Hi,
Just want to ask what will be the effect if I will use an external oscillator (32.768kHz) with a CL nearly at max specification, let's say 12pF.
Thanks.
Hi,
Can we send a message from a Provisioner to a Unicast address in a mesh network?
I'm using nrf52832 and can send orreceive message between nodes in the mesh but I...
Using 4-bit SPI mode on the Display Controller side: SCL,MOSI,MISO ... and DCX (by which the controller distinguishes between command bytes and data bytes). There's no obvious...
